I said "about" 42mm cause it is "about" 1 5/8". The op, I believe, just wanted a measurement that would let him know how the mod might look with the tank on it. .725mm would not mean much. Plus it measured slightly below the 1 5/8" mark on my tape measure.(so what does that calculate to?
) As far as 13mm to replace 1/2", it makes little difference with wrenches that 1/2" is actually 12.7mm. Typical engineer thinkin, like you said. 
Oh, Okay Jingles. I thought you were going for another older one.
You're in already Alle! Here's your new t-shirt.If tracking is correct, I should have a GS Air M and GS Air MS tomorrow! Since I love the 2 original GS Airs I bought, I felt the need to try the newer models (although I did order another original one also).
You are quite welcome, my friend! Sooner than later,I have received the new TC GS Tank courtesy of a very generous member here (Take a bow IMRs!)
While I don't have any TC mods, I was anxious to take this tank for a test spin...
Installed one of my recoiled, rewicked Air coils in it, filled with DIY Strawberry-Cheescake and jumped in
the driver's seat.
This tank rocks, The AFC is very nice! I thought maybe they would put in some sort of click stop with
the holes, but no. It is pretty tight and stays where you put it.
Draw is very nice, don't know about noise reduction, I'm old and deaf...
they have really enlarged the fill holes! Easy-peasy to refill now!
They did away with the trough around the coil in the base.
Short drip tip like the MS, works fine.
Only drawback is the capacity...
I will break down and get some more of these...some day may do TC, but for now it's
a great regular coil tank.
Thank you, IMRs! You the man!
Might be tall enough to work in this with the stock drip tip. It'd definitely be stealthy. Just wonder if it's too fat...
Oy... may the force be with you...
Oh, Okay Jingles. I thought you were going for another older one.
You're in already Alle! Here's your new t-shirt.
View attachment 478929
@AllElseFailed -- Did I forget to welcome you? You're an AIRHEAD, full-fledged, 100% DID WE MISS ANYONE ELSE???
It measures a little under 3/4" (about 18.5 to 19mm)(19.05mm for the injunears) so it probably will.
If it fit's it'll be close. Probably a little short, too. The M is just a bit shorter than the ST Nano and it sits SLIGHTLY recessed in this mod, itself. The stock drip tip should work fine though... maybe the eGrip drip tip if the stock one is too short for comfort.
Just put it in my cart online and the price in the us is 33.33 pounds (no VAT here in the US)... looks like they offer free snail-mail shipping, too. That comes out to about $52. Standard shipping is 10 pounds, bringing the total with it up to about $67.
Yep. It really takes about a half to a full tank to break in the coil. After that... smooth city with a bit of bitterness... just like real tobacco.Got the Reaper in Cloudmann. My first impression was too rich and funky. After vapin it just 15 minutes, it's startin to grow on me. It's like a fairly good cigar at this point. I can see how it could be a satisfying vape for a smoker. I also think it would be excellent for ex smokers to keep around in case they get a craving for tobacco. It's very smooth and the tobacco flavor is outstanding. But I don't know about addin menthol considerin the flavors I'm getting from it. It might not be compatible but I will experiment later. Thanks for the recommendation. Yep, during the time I typed this, I've decide it's a definite keeper.
Might be possible to install the afc base after putting the top of the tank into the mod upsidedown... I don't see why not. Really doesn't matter (to a reasonable limit) if the ring width is slightly high.
That's the difference between Stanley and a set of calipers or a micrometer, I guess.
You could sand or grind the knurl off if need be.a
That's the difference between Stanley and a set of calipers or a micrometer, I guess.
