Eleaf GS Air Fan
- Thread starter Javamon
- Start date
- th_trl_thread_readers 0
- Status
The center pin is in the center..........OMG! You guys know SO much about all of this. I don't even know here the center pin is!
Mud, you can not believe the day I've had. Getting the PM to you now.
Edit: No language please.....
Part of the problem is that I would literally have to go out and get everything in that video. The wire cutters, the wire, the needle... everything, with the exception of the rayon, which one generous member has so kindly offered to donate.
In case you haven't noticed, I'm not exactly the type of gal who just has that stuff lying around the house.
Edited because of redundancy.
You really don't, Lost. You can try to rebuild with whatever you have handy--even plain cotton balls from a drugstore, organic preferably. All you need is some kind of a metal rod (a drill bit, a piece of a wire clothes hanger from dry cleaners or a large nail, whatever, heck, you can even use a toothpick) ca 2mm diameter and you're set. You can use nail clippers or you can twist the wire off. Honest. That's how I started. Your istick will read your coil's resistance so you don't even need an Ohm's reader.
I built my first coil with a q-tip for the cotton and to wrap the wire with a pair of small scissors to cut. Looked and worked pretty good. All you need to buy is some wire. That is until you can get some good stuff together. Its all cheap
The center pin is in the center..........
Edit: No language please.....
I saw that coming.
Nope. No spitting here. Snap crackle and pop sounds are OK, but not spitting. Check the connections in your tank, gaskets, o-rings... Lower wattage is necessary. It should not spit.
Again, no browning here. I hate when that happens. The only atty that it to me was the eGo-C... And cartomizers, of course. Don't know what to tell you.
You're welcome...I saw that coming.
...............my daughter is blonde so I'm used to bein needed......She also never reads this forumHonestly, not a fan of those. They are easy, but you can't put any tension on your coils, and tension is critical.
Just my
Well I think I have a coil that's on it's last leg. I'm vaping a juice that I LOVE, which is a little darker and I think it's shortening the life span of the coil. The ohms changed today from 1.5 to 1.6 and now I can't seem to vape it at as high of a wattage as I have been or I get a slight burnt taste.
Okay Cheechako, where do I send it?
Typed with a big, fat Tabby sitting on my lap between me and my laptop. Please excuse any errors.
I'm vaping a juice that I LOVE, which is a little darker and I think it's shortening the life span of the coil. The ohms changed today from 1.5 to 1.6 and now I can't seem to vape it at as high of a wattage as I have been or I get a slight burnt taste. Okay Cheechako, where do I send it?
Typed with a big, fat Tabby sitting on my lap between me and my laptop. Please excuse any errors.
Many long debates.
Usually a combination of high heat (or not enough heat ) and all kinds of additives that end up as gunk on the coils. That's why I dry burn or rebuild often. Dirty coils are a bad thing.Probably not, the only tank/tanks I have that do that are kanger subtanks. I figured it was due to that massive hole in the top of the coil exposing a relatively large diameter coil and lots O air pulling thru and up out of it. But I could be wrong.
I've had spitting cartos too. Usually it's da juice in da center airflow tube--or too much heat.
Birdie, I get the spitting all the time, and all the other Rice Krispies sounds. I notice the spitting mostly if I haven't hit it for a while. That's when I usually give it "priming" fire away from my face to let the juice pop out somewhere other than in my mouth. That almost sounds obscene.
I love 29... Just sayin. Easier to work with than the 30, and not quite as thick as the 28. And it heats up and cools down fast.
thanks Cheechako for the coil building video..
I rebuilt my first coil.. used 10 wraps 28ga on a 17 gauge needle with rayon.. for the outer layer wrap I used some of my old supply of Lipton pyramid tea bag material..
It came out to 1.4ohm and is vaping great.. I have used about 4mls so far and no flooding,gurgling or leaks..
The Gs-air is quite the tank.. my gennies are feeling lonely, since I got it..
Thanks to the op for posting about it..
Genius! Why didn't I think about it! I have tons of those.
'No atomizer' means usually no electrical connection. The center pins don't make contact. The more you tighten your atty, the bigger the risk of depressing the center pin and making the contact even less likely.
Rule #1: Do not over tighten. Whatever you do--do not over tighten you atty onto the battery.
Try to pull that pin up a tad or get a few circuit board spacers from Madvapes. The links to MadVapes don't work here, for some reason, but this is what you need:
You just drop one of those into your mod's 510 well and you're good.
OMG! You guys know SO much about all of this. I don't even know here the center pin is!
Mud, you can not believe the day I've had. Getting the PM to you now.
Birdie, I get the spitting all the time, and all the other Rice Krispies sounds. I notice the spitting mostly if I haven't hit it for a while. That's when I usually give it "priming" fire away from my face to let the juice pop out somewhere other than in my mouth. That almost sounds obscene.
A little extra action after a long break is to be expected--as the atty is sitting idle, extra juice accumulates in the atomizing chamber and may get expelled violently.
Primer puffs help.
- Status
Similar threads
