Should I inject 1 ml max ?? Also where should i inject ?? Should I puncture the pollyfill and inject past it ?? I don't know what's exactly inside Boge and resserectur cartos.
Filling Carto with a syringe , where to inject exactly ??
- Thread starter Youmadbrah
- Start date
- th_trl_thread_readers 0
- Status
If you're going to use a syringe on Boge the same filler type cartos just insert the needle into the filler. Stay closer to the wall of the carto so you don't bump the coil/wire and slowly inject juice going slow enough to give the filler time to absorb the injected juice. When it's full you'll see the filler get glassy on top and won't absorb anymore. I usually lightly blow through one end of the carto to make sure I've got any excess out. Wipe down the connection to make sure it's dry and you're ready to go.
Push the needle down into the polyfill towards the connectora bit while injecting. I usually inject into 4 different places in the polyfill to make sure the liquid is distributed evenly. When you see the liquid reach the top of the carto you are usually done. You can add a bit more liquid and then suck it back into the syringe if it's overfilled.
If there is a filler around the coil(s) , whats the point of the thick pollyfill on top of carto??
Do NOT push the needle thru the polyfill. You could move it and break a wire. You want to put the needle between the wall of the carto and the filler so you dont move it.
This is a copy and paste I wrote for someone else on how to fill the Ressurectors. Do the same thing for the Boges, they just hold less juice. The Ressurectors hold alittle over 2ml of juice and the Boges hold 1ml-1.2ml. Follow these directions exactly and you should have no problems. I don't know what kind of needle your using, but I recommend using a syringe with an inch and a half long needle. That way it will go all the way to the bottom of the Ressurectors.
Here ya go:
How to fill a cartomizer with a syringe:
"All you have to do is take the dropper part of the bottle off your juice and fill your syringe with 2ml for a new carto. Take the rubber tip off the carto and carefully insert the needle down the side pushing against the metal. DO NOT go thru the filler because it will move it and you could potentially break a connection and your carto. Slide the needle down the side and go all the way to the bottom. Then slowly start dispensing some juice. Dont dispense it all bc then it won't be evenly distributed. Put alittle in, then take it out and insert the needle in a different spot. I normally do it in 3 spots (in a triangle) I found it distributes the best, but you could just do it in 2, on opposite sides. Make sure the needle is at the bOttom bc then you will not have to wait at all for it to settle. Disperse slowly and you will begin to see the toP of the filler become slushy. It is full then, don't put more. If its a new carto is will def hold 2ml, if your refilling it won't take a lot so pay attention and once it gets alittle slushy stop. While your filling hold a napkin or something under the carto bc if you do it too fast a few drops will come out the battery end. If that happens its only bc you did it too fast and the poly fill didn't absorb quick enough.( that happens to me bc I am impatient and fill it in about 10 sec, so I just hold a paper towel or napkin underneath.) wipe up the drops and put the rubber cap back on the carto. Then put the carto between your hands and rub back and forth spinning the carto quickly. This will insure the liquid is evenly distributed in case you put too much on one side from the syringe.
Now you have a perfectly filled ressurector that is ready to be used right away!"
It's really easy to do and I think tou pick it up very quickly. Just watch the top of the filler carefully and fill slowly and you will see the juice rise to the top of the filler. Once the top becomes slushy, it's full.
Hope this helps and let me know if you have any questions
This is a copy and paste I wrote for someone else on how to fill the Ressurectors. Do the same thing for the Boges, they just hold less juice. The Ressurectors hold alittle over 2ml of juice and the Boges hold 1ml-1.2ml. Follow these directions exactly and you should have no problems. I don't know what kind of needle your using, but I recommend using a syringe with an inch and a half long needle. That way it will go all the way to the bottom of the Ressurectors.
Here ya go:
How to fill a cartomizer with a syringe:
"All you have to do is take the dropper part of the bottle off your juice and fill your syringe with 2ml for a new carto. Take the rubber tip off the carto and carefully insert the needle down the side pushing against the metal. DO NOT go thru the filler because it will move it and you could potentially break a connection and your carto. Slide the needle down the side and go all the way to the bottom. Then slowly start dispensing some juice. Dont dispense it all bc then it won't be evenly distributed. Put alittle in, then take it out and insert the needle in a different spot. I normally do it in 3 spots (in a triangle) I found it distributes the best, but you could just do it in 2, on opposite sides. Make sure the needle is at the bOttom bc then you will not have to wait at all for it to settle. Disperse slowly and you will begin to see the toP of the filler become slushy. It is full then, don't put more. If its a new carto is will def hold 2ml, if your refilling it won't take a lot so pay attention and once it gets alittle slushy stop. While your filling hold a napkin or something under the carto bc if you do it too fast a few drops will come out the battery end. If that happens its only bc you did it too fast and the poly fill didn't absorb quick enough.( that happens to me bc I am impatient and fill it in about 10 sec, so I just hold a paper towel or napkin underneath.) wipe up the drops and put the rubber cap back on the carto. Then put the carto between your hands and rub back and forth spinning the carto quickly. This will insure the liquid is evenly distributed in case you put too much on one side from the syringe.
Now you have a perfectly filled ressurector that is ready to be used right away!"
It's really easy to do and I think tou pick it up very quickly. Just watch the top of the filler carefully and fill slowly and you will see the juice rise to the top of the filler. Once the top becomes slushy, it's full.
Hope this helps and let me know if you have any questions
Also after its filled, I normally blow lightly to clear any juice out of the airtube. If you hold it up to a light, you should be able to see thru the carto.
I also take a straightened out paperclip and CAREFULLY put it thru the threaded end and basically bore out the airhole. This is necessary to do but it helps the airhole not clog up so quickly. Just make sure you don't force it. If it gets caught, wiggle it around slightly until it easily goes thru the tube. If it gets caught and you force it you could break the coil so be careful. Again, you don't have to do this, but I find it helps clear any juice out of the air tube and helps it not gunk up as quickly
I also take a straightened out paperclip and CAREFULLY put it thru the threaded end and basically bore out the airhole. This is necessary to do but it helps the airhole not clog up so quickly. Just make sure you don't force it. If it gets caught, wiggle it around slightly until it easily goes thru the tube. If it gets caught and you force it you could break the coil so be careful. Again, you don't have to do this, but I find it helps clear any juice out of the air tube and helps it not gunk up as quickly
I prefer to use a can of air and spray threw the battery side myself. That will usually take away anything inside including the juice.
- Status
