Poor Roxy, "more mesh" is probably the last thing she wants to hear
Flash-e-Vapor V2 rba by Artur Schwarze
- Thread starter dice57
- Start date
- th_trl_thread_readers 0
- Status
It is, but it won't have to be so tight. If I block the airhole a bit, the flavor is crazy good.
I know.. Mesh
I did use a microcoil in the screw threads once, it worked. A micro coil of different gauges could fine tune it over what the screws can if needed... But found I like the v2 wide open anyway..
I finally got mine at post 138 and mentioned the micro coil..
I did use a microcoil in the screw threads once, it worked. A micro coil of different gauges could fine tune it over what the screws can if needed... But found I like the v2 wide open anyway..
I finally got mine at post 138 and mentioned the micro coil..
Last edited:
Well, the v3 is up and running, but my hands are deadIt took me almost 2 hours to roll that mesh. I guess rolling mesh is my personal hell.
Just had a thought on rolling mesh, I wonder if you took a large sewing needle like used for leather and use it to get the mesh into a rolled shape. If you cut a longer then needed piece of mesh, cut a tapper point on the mesh and run it through the eye of the needle then roll the mesh? Once you get it rolled it will hold a rolled shape, you can unroll it and trim the point off. You can work the mesh from there, for me getting the roll started is the hard part. I have taken mesh out of the Flash-e, unrolled and trimed it, rolling it back up is easy. Tomorrow I'll have to experiment and see if it will work, I have an assortment of large sewing needles.
I do really well with the first half, and then have trouble keeping the tension for the second half. Then when I'm done, its way too big to fit in the hole. I don't know how sedge got 60mm long pieces in there. I finally had to cut it down to about 40mm for the v3 and probably more like 30mm for the vs.
I know huh. He used 110 too, coarse as a mother. The guy is a mesh master, a Steele weave wizard, lol
I used 110 also. Cramped hands, numb, cut up fingers. Ugh. Well, my worry that they weren't good enough seems unnecessary. They're both working well. I've vaped 1/3 of the v3 and half the vs.
Fluffed up weeks definitely help keep things in order As long as the feeders aren't feeding too little, it seems to be pretty forgiving.
Wondering if ss-rope would do the trick.
Naturally you will need a little mesh and cutting it to size might be a pita.
Sent from my iPhone using Tapatalk
Naturally you will need a little mesh and cutting it to size might be a pita.
Sent from my iPhone using Tapatalk
Yeah bud, you've found a real winner, especially when it comes to TH imo.
That must be the key, when you've hand rolled 100's of "cigarettes" its a piece of cake to roll mesh with two fingers.
Oh, well its a lot easier with 350 mesh!!!
Last edited:
Never say never, Origenny is fantastic with a cotton build, don't have to roll mesh if you don't wantI did make a decision today that there will be no more gennies
Yeah, the idea of a dual coil genny with mesh just makes me groan. My hands hurt so bad most of the time, and after setting up the Flash e's it will be several days before I return to even my customary level of pain.
Not sure why it's difficult to prep the mesh.....you know how people use scissors to "curl" ribbon so it goes all twisty (like for wrapping a present)? You can do that with your mesh strips. This will prep it to make it easy to roll.
I did that actually. Its hard because I have bad, degenerative arthritis and neuropathy.
It does
. Even a few years ago, it would've been easier. It may even have been easier if spring would show up. 36° right now and was snowing this morning.- Status
