Focalecig ... A new Fasttech??

[Nikkita6]

I love the kayfun and Taifun custom caps too .. I love it set up with my Russian and ZNA 30 But I am a bad mommy, because I have not put the Taifun cap on any of my neglected babies yet. I used to be sooooo Pro-Taifun, yet I have touched either of mine since the end of May

I have the full and nano clear tanks for it too .. I will get to it. I just have been vaping whatever is new in the mail lately. And I haven't even built and vaped the Rose yet, but I was waiting for my new camera to come to so I can photograph it while its clean out of the box before I vape on it.

@Nikki Lol.

I'm loving these new top caps for the Kayfun and Taifun. Finally able to get my Kayfun up and running. Had all 3 Kayfun positive post snap on me. Got a .54 24ga in both. Both are kicking my Fogger and Lite in the .....

 

[yOGi805]

It's not a v2 Orchid, thats for sure. The tobeco clones I bought are the version 2s with the bottom fill screw. I tried top filling mine the other day because I didn't have an extra needle tip bottle and was using a glass dropper. I ended up with juice all over. :/


Sent from my iPad using Tapatalk

 

[bsoplinger]

Sure is, the finish on both match prefect, as if they was made for each other

Glad to hear me asking about it got you a working mod. They do look good together. Is that a quartz kit, with those red o-rings? They look nice on the Russian?

Sent from my Nexus 7 using Xparent Purple Tapatalk 2

 

[Crocky]

It's not a v2 Orchid, thats for sure. The tobeco clones I bought are the version 2s with the bottom fill screw. I tried top filling mine the other day because I didn't have an extra needle tip bottle and was using a glass dropper. I ended up with juice all over. :/


Sent from my iPad using Tapatalk

I did not even notice that. Thanks for pointing it out. I definitely want the bottom fill hole. Says 2.4 in the description.
Not sure what that means

 

[Nailz]

Glad to hear me asking about it got you a working mod. They do look good together. Is that a quartz kit, with those red o-rings? They look nice on the Russian?

Sent from my Nexus 7 using Xparent Purple Tapatalk 2

Yes it is, it is the kit that is in the US warehouse, best looking tank setup I've got

Also thanks for inquiring about the 4nine, if you hadn't brought it up, would still be sat on the shelf not being used

 

[yOGi805]

Is focal going to carry a kayfun quartz nano kit in the us warehouse? They are supposed to fit the orchid.


Sent from my iPad using Tapatalk

 

[Nikkita6]

Is focal going to carry a kayfun quartz nano kit in the us warehouse? They are supposed to fit the orchid.


Sent from my iPad using Tapatalk

Yeah .. silver and back, you didn't see them? Ships in a box with an extra glass tank too.

 

[yOGi805]

Yeah .. silver and back, you didn't see them? Ships in a box with an extra glass tank too.

Those appear to be the standard sized ones.


Sent from my iPad using Tapatalk

 

[hobbes4]

I received my Hana clone from the group buy today. Seems to work great but the voltage only displays when I hit the fire button. When not firing it reads 0. Ohm and watts display all time and seem accurate. Is it suppose to be like this or should the voltage always display too?

 

[Portertown]

I received my Hana clone from the group buy today. Seems to work great but the voltage only displays when I hit the fire button. When not firing it reads 0. Ohm and watts display all time and seem accurate. Is it suppose to be like this or should the voltage always display too?

I have not seen one of these clones, but I do have a real DNA30 mod and it displays just the same as yours is. It only shows the voltage when the fire button is pressed and all other times it just shows 0 volts.

 

[Nikkita6]

Those appear to be the standard sized ones.


Sent from my iPad using Tapatalk

Oh my bad .. yes those are the full size quartz tanks ... I didn't read what you wrote properly

 

[Nikkita6]

I received my Hana clone from the group buy today. Seems to work great but the voltage only displays when I hit the fire button. When not firing it reads 0. Ohm and watts display all time and seem accurate. Is it suppose to be like this or should the voltage always display too?

That is how the Evolv and clone DNA 30 chips behave, so yes, it is perfectly normal. Yihi 30 W chips are different though, like the Wotofo ZNA 30. The voltage is constantly displayed.

 

[Portertown]

I received my copper Manhattan style mod from the FC group buy this week and I am quite satisfied with it. I do not know who made it as it did not come in a box, it was just in bubble wrap in an envelope. It was very clean and I did not have to do any cleaning on it at all. I am surprised that it came halfway around the world and still did not have a speck of tarnish on it. The switch button throw is a little shorter than the ones by Acerig. The only thing I have found on it that was not perfect was the top cap was ground flat on the top and the edge was not then rounded off. This left a sharp area on the edge of the top cap which I easily rounded off with some fine sand paper. It came with the three different length 510 positive pins which allows for the flush mounting of different atomizers.
If I had known the quality of these mods was this good, I would have ordered more than just one of them.

 

[hobbes4]

Thank you Portertown and Nikkita6.

 

[Portertown]

Thank you Portertown and Nikkita6.

Glad to help a fellow vaper anytime.
Please report back after you get to use your mod for a bit and let us know how it is performing for you.

 

[f1vefour]

Why does it seem like orders from focalecig get here so much faster than those from FastTech?

It's likely because FT does much more volume. Have you seen how many products FT carries, it's insane. So it is impossible for FT to get all orders out the door everyday, they simply provide shipping information and ship it as soon as possible..often it takes a couple of days.

 

[Nailz]

Wow Focal is on the ball, Orchid V2 already hit new arrivals

Tempting, but I am going to hold off and see if they do a split chimney and glass tank on the V3

 

[young gotti]

received my hana mod from the group buy, so far so good, even my kayfun which only fires on one mod i own fires on this so i'm pretty happy about that....even though this seems like a nice sized mod....hopefully someone clones the vaporshark soon as it seems thinner...or ppl make it look smaller and my hands are just small

 

[inswva]

I received my Hana clone from the group buy today. Seems to work great but the voltage only displays when I hit the fire button. When not firing it reads 0. Ohm and watts display all time and seem accurate. Is it suppose to be like this or should the voltage always display too?

Received mine this morning.

The box is nice and beefy. No finish blemishes and the battery door sits flush. Display screen is aligned properly in the window. The OLED is clear and bright. USB connector is aligned and flush. Internally, I can tell there must be a copious amount of hot glue under the plastic protector which covers the electronics - glue is emerging from quite a few places in the gaps around the plastic. I probably won't bother looking under the protector unless the board fails and I end up putting in a genuine Evolv board.

Display reads "Evolv DNA" upon waking up. It wakes up very quickly. Resistance readings are dead on. Unfortunately, my rebuildables have yet to arrive so I'm running the box with my Nautilus full and mini with BVC coils. Both attys sit flush and the 510 connector is properly aligned. Buttons are properly aligned and nice and clicky. All in all, it appears to be a nicely constructed little box, save for the mess of hot glue I'm guessing lurks under the plastic cover.

15W seems to be about all my BVC heads are willing to endure. Actually backed it off to 14W but it hits nicely, certainly better than the 11W MVP it is replacing.

Gratuitous pics (I'm certainly no photographer):

 

[inswva]

received my hana mod from the group buy, so far so good, even my kayfun which only fires on one mod i own fires on this so i'm pretty happy about that....even though this seems like a nice sized mod....hopefully someone clones the vaporshark soon as it seems thinner...or ppl make it look smaller and my hands are just small

I believe HCigar has a VS clone on the way.