GG, GGTS, Odysseus Base tight draw fix & HIGHLANDER COILS Dual .8 ohms @ 25 Volts

[Bishopheals]

8-oGG, GGTS, Odysseus Base tight draw fix & 25 Volts Ody8-o


Some users mention of a tight draw when using GGTS base Odysseus. Here is an easy how to do of clearing that up. First Odysseus doesn't leak. Its not suppose to leak. If juice control is left open while not in use it can very well leak. me a chain vapor I make it a habit every time I put it down on side to close juice control and re open when I use it.


At times if left fully open with a tnak fully loaded of juice guess what? IT's going to leak. Also it may not be the jucie control it can be that condensation built up it all depends how hot your vaping and if your a chain vapor like I am. I will show you how to clear it out in a quick 1,2,3 method and you will be off vaping like a KING.


hope you found the video useful if you have any questions feel free to email me or pm me on the ECF forums.


Highlander coils will not break. .8 ohm dual at 25 volts it wouldn't be possible without Manos. Please don't try this at home leave it to the vaping crazy professionals LOL.


GGTS is obtainable at Clouds of Vapor. 8-o8-o
Welcome to Clouds Of Vapor

 

[Devonmoonshire]

Dang Bro!!! That was IN SANE!!!!!!!! Great tips though on the cleaning and airflow. I do that to my GG every time I change coil/wick, give it a thorough cleaning and I never have a problem with airflow or function at all.

There are reasons that this is billed as an advanced user device. It does take more knowledge of how these things work to operate to it's fullest potential, which seems at this point to be pretty much limitless as far as options go

Have a great Night;
Nate aka Darth Vapor

 

[Bishopheals]

U welcome bro, I mean I do that in middle of day too. sometimes if i had it down for a few hours whats a quick blow to get some condensation out.

GG products are phenomenal why do you THINK ITS GG GOD'S GIFT!!!!!!

 

[imeothanasis]

sometimes I do things and I think that all people do them, like cleaning the juice out of GG. So I never mention some of my actions, I am very used to them. I usually put GG under water and thats it.

But you video saw exactly what people have to do often and that is a great simple tip about air Bish. Thank you very much for this video, for the previous ones and for the future ones too!!

Vaping at 25 volts is not very safe but its an experience for sure. I havent try Ody at those volts but I will try it making a coil at 4 ohms with a doubled wick. Thats a 6,5 ampere through atomizer and 156 watts. I really want to feel this experience with an atomizer that can do that.

 

[Bishopheals]

Your products make it happen my friend. Though I did say to everyone not to do this I was just showing how powerful and how GG GOD'S GIFT can put out not like other products that are limited.

 

[imeothanasis]

I heard you many times saying to people to not try it at home Bish, thats is an exellent advice. But it was tempting for me! lol

 

[Bishopheals]

I heard you many times saying to people to not try it at home Bish, thats is an exellent advice. But it was tempting for me! lol

You should of seen Manos and I this past weekend on skype. It was so funny as hell. We were like dragons vaping on GG.

 

[imeothanasis]

axaxaxa, that would have fun Bish

 

[Bishopheals]

I just wanted to show that these Highlander coils thanks to manos it don't break. LOL plus I'm waiting on a shipment of new wires that I will be testing out to see how much further in vaping heat I can go.

 

[Devonmoonshire]

I just wanted to show that these Highlander coils thanks to manos it don't break. LOL plus I'm waiting on a shipment of new wires that I will be testing out to see how much further in vaping heat I can go.

LOL Yeah there is no way I could handle that kind of heat, just dropped my nic level to 12 and it still hits really hard, but manageable for me, I could not handle the voltage and massive heat you do with the baseball bat GG you made up LOL That thing is HUGE and Awesome Looking

Nate aka DarthVapor

 

[Roxxette]

I clean the collector tank everytime i finish the tank, very rarely i refill with the same liquid so i just clean everything and take out the rebuildable part; once a week i polish the brass contacts.

 

[Bishopheals]

LOL Yeah there is no way I could handle that kind of heat, just dropped my nic level to 12 and it still hits really hard, but manageable for me, I could not handle the voltage and massive heat you do with the baseball bat GG you made up LOL That thing is HUGE and Awesome Looking

Nate aka DarthVapor

buddy if its to hot you can always make the two coils at 1.0 ohms
it will still be powerful with a minor decrease in heat. Sometimes i like leaving my tongue close to mouth piece for the added heat but then i tend to move it away if its gets to hot.

 

[Devonmoonshire]

buddy if its to hot you can always make the two coils at 1.0 ohms
it will still be powerful with a minor decrease in heat. Sometimes i like leaving my tongue close to mouth piece for the added heat but then i tend to move it away if its gets to hot.

WHOA!!!!!!!!!!!! Okay I made on of the highlander Coils !!!! Holy Mosses That is Intense!!!! I used the V1 Ceramic and Ceramic casing for it as it was a little easier to work with for some reason and since I have both V1 and V2 I made a Really Intense 0.7 Ohm Dual coil for Ody on the V1 Ceramic just in case the Highlander was way too intense, even at 12mg Nicotine it was Absurdly Strong I love it, I vaped it till I burned it Whew that thing is Wild!!!!!

You are correct, this takes a lot of precision to do so to all the novices out there, Have Patience, it takes a great deal of care to do this coil, but if you like Hot Vapes, this is definitely where to get it

GG Vaping!!!! Where the Wild Things Are

Nate aka Darth Vapor

 

[Bishopheals]

WHOA!!!!!!!!!!!! Okay I made on of the highlander Coils !!!! Holy Mosses That is Intense!!!! I used the V1 Ceramic and Ceramic casing for it as it was a little easier to work with for some reason and since I have both V1 and V2 I made a Really Intense 0.7 Ohm Dual coil for Ody on the V1 Ceramic just in case the Highlander was way too intense, even at 12mg Nicotine it was Absurdly Strong I love it, I vaped it till I burned it Whew that thing is Wild!!!!!

You are correct, this takes a lot of precision to do so to all the novices out there, Have Patience, it takes a great deal of care to do this coil, but if you like Hot Vapes, this is definitely where to get it

GG Vaping!!!! Where the Wild Things Are

Nate aka Darth Vapor

OMG .7 you should see my .6 dual coil. LOL i got that on my ody instead of pen. On pen to hot very very very very hot its like walking on the beach in sand bare foot with no sandals. HOT TITTYS HOT TITTYS!!!!

It takes time to get a good hang of making these single coils the trick is to keep the junction points small. Manos advised me its ok to twist the NR and RW coil all the way up but when you stretch the legs of the coils RW with NR what is recommended is to loop over the None RW only 3 times that’s it. Then cut the tail off. That way your left with a smaller junction point and easier to manage if its outside of channel or inside ceramic cup of Odysseus or Penelope.

I also worked on another technique that I was experimenting. I mentioned to Manos to try to destraining the wicks. This somehow helps absorbing the juice faster and you get to produce more vapor and heat with each vape. It’s in my vids when I use 3 strands of wick for the two single coils and one 3,5 wick in middle for sandwich for Ody and for pen I just remove 2 strands from the 3.5 wick that will act as my middle wick is all.

In all honesty you think someone would need a kick with this build? FORGETABOUTIT!!! you can adjust lowering heat by making higher ohms is all. a few folks I know tried it and they agreed didn't need to use kick and they loved the heat production that the kick didn't give them compared to this build. One steady connection no need to finagle and move around parts etc.

 

[Devonmoonshire]

OMG .7 you should see my .6 dual coil. LOL i got that on my ody instead of pen. On pen to hot very very very very hot its like walking on the beach in sand bare foot with no sandals. HOT TITTYS HOT TITTYS!!!!

It takes time to get a good hang of making these single coils the trick is to keep the junction points small. Manos advised me its ok to twist the NR and RW coil all the way up but when you stretch the legs of the coils RW with NR what is recommended is to loop over the None RW only 3 times that’s it. Then cut the tail off. That way your left with a smaller junction point and easier to manage if its outside of channel or inside ceramic cup of Odysseus or Penelope.

I also worked on another technique that I was experimenting. I mentioned to Manos to try to destraining the wicks. This somehow helps absorbing the juice faster and you get to produce more vapor and heat with each vape. It’s in my vids when I use 3 strands of wick for the two single coils and one 3,5 wick in middle for sandwich for Ody and for pen I just remove 2 strands from the 3.5 wick that will act as my middle wick is all.

In all honesty you think someone would need a kick with this build? FORGETABOUTIT!!! you can adjust lowering heat by making higher ohms is all. a few folks I know tried it and they agreed didn't need to use kick and they loved the heat production that the kick didn't give them compared to this build. One steady connection no need to finagle and move around parts etc.

I totally Agree, I took the Kick out over a week ago and have not touched it since, I do not in any way need a kick to get my perfect vape. All I needed was to make a two wrap dual coil with double wick design and ....... BANG!!!!!!!!!!!!!!!!!!! Superb Vape Every Time and you wanna talk about battery life???? Man this thing lasts me a day or more before changing batteries. I just measured the ohms on the dual coil I made this morning and it is fluxing between 0.5 and 0.7 now that I have been vaping on it for a few hours. Whew!! The Hit, The Heat!! The pure taste!!!! It is All There, all there and perfectly matched!!

I gotta go check out a hunch I have, I know they make tool for twisting wires together and I am gonna check out Lowe's and see if they have one in an Extra Tiny size to use for these delicate wires to make a more streamlined joining point so it is small and nice and tight

If this pans out I should be making the Highlanders very easily every time and perfect every time

Nate aka Darth Vapor

 

[Bishopheals]

Devon your going to love what manos and I did today. oh snap

 

[Devonmoonshire]

Ruh Roh... I am Trembling with anticipation, this whole custom designing coils is addictive to say the least Especially for a Twiggit like me

Can't wait to see whatcha Got goin Brother
Nate aka Darth Vapor

 

[Bishopheals]

its uploading now it be ready real soon.

 

[Devonmoonshire]

Woooo Hooooo!!! I can't wait Bro, this sounds like it is going to be EPIC!!!

Nate aka Darth Vapor

 

[Bishopheals]

almost done, we were experimenting with a few video recording apps so some of the video of the video chat wasn't compatible for the rendering app. So i had to cut how we made the coils clip out.

I explain how its done plus i think manos would like for me to do one on a separate video when i get my 36 gauge wires this week.