GOT MY P+ TODAY that I won in the contest

[k3vin]

WOW,very nice 18350,and the very first ONE ever manufactured.

I would like to thank the academy,and..umm...woops hold on,wrong forum..

I would like to thank David for the fine mod,which it is,and it is now home to my HH357 ATTY!!...

And Susan for knowing which number to pick..

And here is a pic of my HH357 snuggled up nicely in its new home..

Thanks again so much David,and for signing it...its an excellent mod and I see why they are costly,they are manufactured to the Nth' degree..
K3vin

 

[forcedfuel50]

Looks like a good match to me! It's Exciting to hear you are liking your new toy!

 

[k3vin]

cant put it down....

 

[forcedfuel50]

Those HH357's, i've never tried one. Are they like a 306 in construction or like a 510?

 

[k3vin]

306 internal,510 casing, no bridge,with what looks to be some sort of steel wool wrapped around the coil cup.

 

[AllanRR]

Very nice. Congratulations! vape it in good health.

 

[forcedfuel50]

306 internal,510 casing, no bridge,with what looks to be some sort of steel wool wrapped around the coil cup.

So the casing doesn't pull off like on a 306 though does it?

 

[k3vin]

That is right David it doesn't pull off. I am using 510 dt's

 

[atavanhalen]

So the casing doesn't pull off like on a 306 though does it?

Nope like Kevin said, the tube does not come off, it is essentially a 510 atty, with a cisco spec 306 coil installed inside, and there are some other modifications having to do with airflow, so it is a very good vapor producer because of a vacuum effect. you must vape a certain way in order for it to work that way though, very hard quick pulls, instead of long slow draws.

@K3vin, glad you got it, and like it, they are totally awesome, and almost maintenance free.

 

[k3vin]

Yea liking it alot

 

[mwa102464]

Those HH357's, i've never tried one. Are they like a 306 in construction or like a 510?

You should try one of these Atty's David, they are super, the cup is wrapped with a wire mesh which seems to hold onto the liquid some too, I find that they need a bit to break in but once they do they are terrific. I actually fill mine with liquid and let them sit for a bit with a condom on the threaded end. Then I screw on the Atty, this seems to soak the internals and help with breaking it in properly. They are the hardest hitting Atty's to date I have use and I think I've tried them all out there. I also bought a handful of them at vaporCon from Cisco and the 3ohm at higher voltages is WIN, there all WIN though

Congrats on that fine WIN k3vin

 

[k3vin]

Yea mwa I'm thinking if going with a higher ohm for higher voltage on my vv pv.

 

[ThatJoeGuy]

Congrats! (holding back the jealousy)

 

[mwa102464]

Yea mwa I'm thinking if going with a higher ohm for higher voltage on my vv pv.

OK but there all WIN k3 all depends on what your vaping and your preferred vape I would say, but there all super no matter what ohm.

 

[k3vin]

I think I will go with the 3.0,as they are out of the 2.5ohm

I have had my 1.5 for a few days now,and it is still like a workhorse..I cleaned it out today with pga,I figure I will clean it about every 3 days..

 

[HzG8rGrl]

Congrats K3vin!

 

[dankie]

Can we se a pic of the signature?

 

[k3vin]

I'll see if I can one sec

He signed it David #1 and the date 10/25/11

it is signed uunderneath the cap where the atty screws into..