The costs of running this huge site are paid for by ads. Please consider registering and becoming a Supporting Member for an ad-free experience. Thanks, ECF team.

HELP!! Igo-w problems!

Discussion in 'New Members Forum' started by Taradise, Dec 1, 2013.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. I swear you don't know frustration until you vape :mad:
    So first I wrapped the igo .. Just a regular 3 wrap with ribbon wire and silica... And I noticed that the button on my mod wasn't working, so I spent a good 15 minutes fixing that.. After getting that situated I couldn't for the life of me get the coils to fire evenly, one would fire, then both, then just one spot on a single coil would burn ridiculously hot..(.hot enough to brake the wire type of hot :evil:) I ended up warping the stupid thing at least 6-7 times!!! Then by some type of miracle I finally did.. So I put it on my ohm reader and it says 1 ohm! I'm thinking that a can't be right so I put a different atty on there and it reads at .4.. So once again, I re-wrapped it a few times, and I just can get the thing to work:confused::confused::confused:
  2. Sthur

    Sthur Vaping Master Verified Member ECF Veteran

    Aug 14, 2013
    Only thing I can think of is are your connections secure?

    Bump for more to look at for you.
  3. UncleChuck

    UncleChuck Ultra Member Verified Member ECF Veteran

    Apr 20, 2011
    Pictures would be very helpful in ironing this out, from the sounds of it the build is a bit of a mess.

    I'm a little confused about what resistance reading you actually got. You say 1 ohm reading on the resistance checker, then you put another atty on there and it read .4? Do you mean you checked the resistance on a different resistance checker, and the reading was different? The way it reads it sounds like you are checking the resistance of two different attys which is why I'm confused.

    Wandering resistance is either a sign of a loose connection (resistance will go up) or a short somewhere (resistance will go down) The IgoW posts are jerks compared to most other RBAs I've build, not sure why, but it seems like it's more difficult to get the wires clamped down securely without breaking them compared to other rebuildables.

    Wiggle your coils around a bit, do they stay in place or can you see the wire moving around inside the post? If it's not screwed down securely you won't get a good connection and your resistance will wander.

    Make sure the coils aren't touching the deck, or touching the posts, or anything like that, which would cause a short.

    Pictures would be very helpful though if possible!
  4. ncvapfan

    ncvapfan Senior Member ECF Veteran

    Jul 24, 2013
    Asheville nc
    sounds like one of the coils is totally shorted. I started building the w with a single coil then worked up to a dual. I'd try that and learn to work the kinks out of one first. Good luck:)
  5. Izan

    Izan Vaping Master ECF Veteran

    Jul 1, 2012
    Mallorca, Spain
    Hi and welcome,
    What wire are you using?
    What length of wire are you using?
    What wick are you using?
    Do you have a multi-meter?
    What device are you using?
    Do you have any other size or type of wire?

  6. izen

    izen Senior Member Verified Member ECF Veteran

    Nov 2, 2013
    I'm sure you'll get it... eventually. (you've great folks here to help & advise you, and), It's not rocket science... Just wanted to comment... I (won't) swear, but I do promise you, with absolute certainty... that YOU don't know frustration if your only frustrations are born of vaping. Hope this is the worst pain you'll experience. :)
  7. MoralFibre

    MoralFibre Senior Member Verified Member ECF Veteran

    Oct 28, 2013
    New Zealand
    At that ohm reading, you've got shorting problems. Keep tweaking the wire! :)

    Give the wire a roasting! - propane it up! :)
    Oxidising and annealing the wire too will help with two things...
    1. Oxidised wire will be far more resistant to shorting (the oxidation really helps there)
    2. The annealing makes the wire more bendable and keeps its final shape better too.

    Good luck and let us know how you get on.
Thread Status:
Not open for further replies.

Share This Page