Huge JUSTFOG S14 Hybrid Tank Giveaway - 500 to be won!

[kcdew]

Hey y'all hope all is well!

 

[Kodak]

Fly by good morning everyone!

 

[Nanny22]

Good morning - am I too late for breakfast, today? I've been stuck on the 404 Error Freeway headed South to nowhere!

 

[GPC2012]

I Think it's just girls I am not being sexist but my boy never crept into our room but my 2 girls do,My 9yr old has grown out of it now and it's been 3 years since she last crept in.but my 5 year old has got such a Temper,
Hits her brother and sister when they wind her up..we confiscated her ipad during the week as she was becoming a nightmare.it hasn't helped...

Makes me happy to be a grandpa now.

 

[GPC2012]

Good morning - am I too late for breakfast, today? I've been stuck on the 404 Error Freeway headed South to nowhere!

We just had a makeshift egg mcroll sandwich for breakfast. So you're not to late

 

[GPC2012]

Fly by good morning everyone!

As long as it's not a drive by


Close but no CIGAR er um vape

 

[Roadtrip635]

Just another use for duct tape!

 

[crxess]

Funny you should say that, @crxess. Looks like since my battery is 10w max and my coil is 1.6 ohm, even when I set it to 4.2v, it's most likely really only putting out 4v. (Found one of the online calculators btw @Fuzzy Thunderbear! Pretty handy!)

I know you don't want to trust tolerances on the board to be spot on accurate, or for that matter trust resistance shift not to occur while vaping.
(Resistance shift) A change in base resistance under load
* Change may occur due to change in metal density .{even had a crossed coil once, that touched loops as it heated up.}
Thin wiring can cause irregular resistance readings under loads due to heat transfer.

Improper regulation, Reading resistance incorrectly, can cause higher than expected output.

******But mostly, you are running your coils at the edge of capability******

New Coil head:
Likely over cooking the e-liquid Reduce power to lowest point where it will vape comfortable.
Gradually increase power while breaking in coil head.
If any burning/dry taste is noticed, back power down slightly.
(Power off pull to saturate wick)
Test at new setting.
If Good - new max setting is achieved. <if needed, reduce further>

 

[SLM]

Quick check in! Hey all!

 

[Phantom-vaper]

Be careful how you build the Nixon, those holes leaking would drive a saint bat .... crazy.

Oh I hate juice leaking outa my RDA onto to my mod....right down the 510 pin it's a nightmare.when you say be careful what do you mean?I Always build my coils so there level and as close as can be to the top of the posts,would that be an issue with the Nixon?

Paul

 

[Phantom-vaper]

Makes me happy to be a grandpa now.

You can fill them full of sweets and send them back to there parents now

Paul

 

[Roadtrip635]

 

[4lph4num3r1c]

Good morning all. I hope everyone is having a wonderful day.

Sent from my LG-H901 using Tapatalk

 

[GPC2012]

You can fill them full of sweets and send them back to there parents now

Paul

And teach them funny off color limericks and jokes to repeat to mom and dad

 

[Shawn Hoefer]

Oh, oh, wait... me, too!

What were we talking about?

Sent from my SAMSUNG-SM-N910A using Tapatalk

 

[GPC2012]

Oh, oh, wait... me, too!

What were we talking about?

Sent from my SAMSUNG-SM-N910A using Tapatalk

C'mon Shawn you can join the fun too

 

[arkansawdave74]

I know you don't want to trust tolerances on the board to be spot on accurate, or for that matter trust resistance shift not to occur while Vaping.
(Resistance shift) A change in base resistance under load
* Change may occur due to change in metal density .{even had a crossed coil once, that touched loops as it heated up.}
Thin wiring can cause irregular resistance readings under loads due to heat transfer.

Improper regulation, Reading resistance incorrectly, can cause higher than expected output.

******But mostly, you are running your coils at the edge of capability******

New Coil head:
Likely over cooking the e-liquid Reduce power to lowest point where it will vape comfortable.
Gradually increase power while breaking in coil head.
If any burning/dry taste is noticed, back power down slightly.
(Power off pull to saturate wick)
Test at new setting.
If Good - new max setting is achieved. <if needed, reduce further>

OH... I'm actually running it at 3.7v on a week old coil and it's doing fine. I was only mentioning what it was like at 4.2 because I didn't understand how someone could run at 80-100 watts, or even 50! But I do now. Thank you for all the input, btw. I'm sure I'll be needing more as it looks as though I'll be graduating to sub ohm sooner than expected thanks to @GPC2012...

 

[Jennifersbody]

Goodmorning

 

[zapped]

Congrats to all of the winners so far!

 

[Myrany]

Waves a paw to say hello from water soaked Louisiana.