-
Need help from former MFS (MyFreedomSmokes) customers
Has any found a supplier or company that has tobacco e-juice like or very similar to MFS Turbosmog, Tall Paul, or Red Luck?
View thread
I'm thinkin' maybe we should try this again? . . . . and you kids should behave yourselves
- Thread starter pdib
- Start date
- th_trl_thread_readers 0
- Status
Chamfer, Chamfer, Chamfer, Chamfer, Chamfer, Chamfer, Chamfer, Chamfer everything!! The air holes really need sum chamferin'. We need a chamfer chuff top fur nuppin'
I'm also going to see if I can get Mundy to come up with some twisted chamfer magic wire to make some dual chamfer coils. It will probably come out to be /~\ ohms.
So in conclusion.... I like the first one. Round is boring, Chamferin' is the future and the chamfer is now.... Just ask the iphony peeps.
Also here is a beedog:
I'm also going to see if I can get Mundy to come up with some twisted chamfer magic wire to make some dual chamfer coils. It will probably come out to be /~\ ohms.
So in conclusion.... I like the first one. Round is boring, Chamferin' is the future and the chamfer is now.... Just ask the iphony peeps.
Also here is a beedog:
That's kind of a personal question but let's just say that I always respond when acute angle starts flirting with me.
Last edited:
nope. littledesign change.change of designs .. . .(that's the escape pod)
can i get one more above what i put on "the list"?
i can always use an escape pod
Are most folks using cotton and KGD in their BF's? I'm using CC and it seems to work excellent but the fact that no juice remains on the deck to speak of kind of makes me think that cotton might be a bit better. I guess I just need to try it but thought I'd ask.
I use both back and forth but seem to lean more towards the ... cotton in general, especially in bf'ers. it just seems a bit better in the flavor for me, insert a loose fluff and it swells up to a nice juicy feed for the coil, rayon needs to be stuffed a bit more because it shrinks but it winds up being a bit more tight to the coil than cotton and I think that it gives me slightly better flavor because of this but truth is there very close to each other
Lately for me it depends on the application. For the Nuppin I prefer KGD. I like the flavor of KGD when combined with NET's.
One of my recent builds has dual vertical coils and the CC seems to draw up and attract to the heat a little better. Could just be my imagination but it does seem to perform noticeably better in that particular application.
Like Turbo was saying though, I also find the flavor really close in both types. I'd give the edge to the KGD when it comes to the Nuppin. I've also started using the soft white center - peeling off the outer layers first. It seems to wick slightly better that way. YMMV
One of my recent builds has dual vertical coils and the CC seems to draw up and attract to the heat a little better. Could just be my imagination but it does seem to perform noticeably better in that particular application.
Like Turbo was saying though, I also find the flavor really close in both types. I'd give the edge to the KGD when it comes to the Nuppin. I've also started using the soft white center - peeling off the outer layers first. It seems to wick slightly better that way. YMMV
OK, ↑ this. . .. .
the last thing I want to do, for all our sake(s), is to theorize and promise, and fall splat in the muck with unhappy people everywhere.
I figured out a reasonably good experiment last night, and engaged.
At about 10pm I "cleaned up" (sort of) my Nuppin' and surrounding area, and then carefully seated the cap as high as I could while still utilizing both o-rings. I continued to vape and even oversquonked (juice covering airholes . . . inside) multiple times over the course of ~2 hrs. I then left it "as was" and picked up on vaping it (and oversquonking summore) this morning, until just a short while ago. Then photodocumented. I had intended to run 24hrs before coming to any conclusions; but the results are so definitive, I thought it was soon enough to submit a report. (it's now been 15 hrs). I will certainly report back if anything changes dramatically.
Last night: "THE SETUP"
Today: "THE PAYOFF"
OK, ↑ this. . .. .
the last thing I want to do, for all our sake(s), is to theorize and promise, and fall splat in the muck with unhappy people everywhere.
I figured out a reasonably good experiment last night, and engaged.
At about 10pm I "cleaned up" (sort of) my Nuppin' and surrounding area, and then carefully seated the cap as high as I could while still utilizing both o-rings. I continued to vape and even oversquonked (juice covering airholes . . . inside) multiple times over the course of ~2 hrs. I then left it "as was" and picked up on vaping it (and oversquonking summore) this morning, until just a short while ago. Then photodocumented. I had intended to run 24hrs before coming to any conclusions; but the results are so definitive, I thought it was soon enough to submit a report. (it's now been 15 hrs). I will certainly report back if anything changes dramatically.
Last night: "THE SETUP"
Today: "THE PAYOFF"
No Niagara didn't happen....BONUS!!!
I feel like I've subscribed to the Bill Nye channel tee hee
if the orings are sealing then the bottom lip makes no difference at all, also any juice that winds up between the 2 o rings from airhole bleed will wind up being minimal and when you pull the cap the lower o ring will act like a wiper and pull the juice up and clean the rim of the atty anyway. I can't see the lip having anything to do with leaking or not leaking
Just a quick add-in as it relates. The Plumeviel has proven successful without the bottom lip. Also some variability in chamber size ability. Same principle though and it's time proven just fine. (Just a bigger atty is all)
Just my
Just my
I use rayon exclusively. It's better for ME. That doesn't mean it's better for the next person.
- Status
Similar threads
- Locked
