Innokin Adept MTL Zlide Kit

[Frenkyou]

I thank NewVaping, the British online shop, for sending me in exchange for an honest review this wonderful innokin adept zlide Kit Mtl from well 3.000mah: Innokin Adept Zlide Kit

NewVaping guarantees delivery quickly throughout Europe, on average (2-4 days).

Package
The Innokin Adept Zlide Kit is represented on the front of the pack with the beautiful "ocean" coloring that we will find inside it.

Later on, in addition to the usual warnings, the content, the batch number, the manufacture at Shenzhen by Innokin Technology, the barcode and the various logos and brands are listed.

At the top is the name of Phil Busardo together with his signature, while in the lower part of the package we find the name and signature of Dimitris Agrafiotis, these two characters: a US and a Greek, often collaborating together for this and other successful ones Innokin branded creations.

Laterally we see the first side which shows the name of the mod and the name of Innokin's tank.

On the opposite side we have a useful blue lace that allows us to open the package very comfortably.

The Innokin Adept Zlide Kit Mtl at first sight.

The package includes:

-1 Adept Mod
-1 Zlide Tank
-1 pre-assembled Coil Plex3D 0.48Ω
-1 Coil Kal from 1.6Ω
-1 Micro-USB cable for charging
-1 Replacement tank glass
-1 Envelope of o'ring
-1 Extra Drip Tip
-1 User Guide
-1 Card with warnings
-1 Guarantee card

Specifications Innokin Adept 3,000 mAh

The Adept mod is small enough to be pocket-sized, but it's not as small as other mods on the market with internal batteries, the Vaporesso Target Mini II or the Innokin Coolfire Mini are smaller, but the Adept is only slightly larger than the Aegis Mini Geekvape (another mod IP67) and with 156 grams, the Adept weighs only 55 grams more. Considering its much higher battery capacity, this is a very acceptable figure.

Adept and its protections for our safety.

The surface of the Adept is covered with a layer of soft and adherent silicone, which makes the kit very pleasant to hold.

At the front of the mod there is a very large smoky color screen that houses the Fire button (above) and the selection button at the bottom.

 

[Frenkyou]

The cup is placed in the center, it can accommodate atomisers with a diameter up to 26 mm without protrusions, although I doubt that you will be able to find an MTL atomizer with a width greater than 24 mm, the pin 510 is floating and gold plated.

Under the mod it houses the micro USB port covered by a black silicon rubber protection that guarantees watertightness (Ip67)
Also on this part we find the references to wattage depending on the type of coil we are going to use.

Through this image we can understand the simple operation of the Innokin Adept.

An arrow at the bottom of the screen points to the left or right according to the coil installed, so we can check the lower part of the device to have the reference on the wattage to be set. The small selection key is then used to modify the power in increments of 1 watt, these steps are represented on the screen by four bars.

With the use of a coil with a resistive value greater than 1.0Ω, the left light indicator is activated, which recalls the wattages of the left column engraved on the bottom of the mod (previously mentioned)

With the use of a coil with a resistive value of less than 1.0Ω, the right-hand light indicator is activated which recalls the wattages of the right column engraved on the bottom of the mod (previously mentioned)

By clicking on the selection button we can obtain the following 4 wattages for the coil with a resistive value greater than 1.0Ω: 11-12-13-14w
By clicking on the selection button we can get the following 4 wattages for the coil with a resistive value of less than 1.0Ω: 14-15-16-17w

Also on the display it is possible to view the charge level of our 3.000mAh battery the LED depicting the battery on the upper part of the power bars lights up every time you vape, and its color indicates the battery level.

- between 100% and 60% the LED is green
- between 40% and 20% the LED is orange
- between 20% and 0% the LED is red

During the recharging operation the LED is red, when charging is completed (about 2 hours) the LED turns off. The mod is equipped with Pass-Trought mode which allows in case of emergency to use it in moderation during recharging.

The mod provides a constant output that will not let us notice any difference in performance until the battery is almost empty. This makes the user experience consistent throughout the internal cell cycle.

Our Innokin Adept MTL according to its IP67 certification, should be dust resistant and waterproof up to 30 minutes at a depth of 1 meter, while the protective silicone layer makes it resistant to impact; it is available in six different colors.

The Zlide MTL tank
It has a diameter of 22 mm, can contain up to 2 ml of liquid and is already a best-seller in the MTL section of the pre-coil coil market.

To top up the liquid, first raise the drip / tip that acts as a safety lock for the Top-cap, then slide the Top by pressing the two red reference arrows.

A cross-section of the Zlide tank and the six pieces that substantially make it up, all easily mountable / removable for effective cleaning.

Platform series

the image below indicates the full compatibility of the coils both for the Zenith and for the Slide.

Impressive the weight of this little atom! well 60gr! This datum surely denotes a great robustness.

Pro
Excellent build quality of both Adept and Zlide
Excellent tactile feel of the Adept
The Adept is robust and impact resistant
Very favorable size and weight
Large, snappy power button
Super easy and very simple circuit for beginners
Good charging time thanks to the 3000mAh internal cell
Zlide is a Tank MTL with excellent aromatic yield (especially with 0.8Ω coils)

Versus
I would have preferred to have the usb socket on the body of the mod and not on the bottom, to leave the Adept standing during charging.
Although the supplied coils are good, I would have preferred to have at least one 0.8Ω coil from the Zenith in the kit (the best for me)

Final impressions

The Adept mod houses a 3000 mAh battery and is able to push only up to 17 watts, which makes it a device that can be used strictly in MTL, in a nutshell, we could not use it with flavor or lung atomizers, this takes them away a bit of versatility, but you are rewarded by extreme ease of use especially in combination with MTL tank like the Zlide.

Using the 0.8Ω coil at 15-16 watts before needing to recharge the battery, approximately 7-8ml of liquid vapors, the cell's life is comparable to that of a good 18650 external battery, enough to cover the daily needs of most. part of people, if not more.

The beginner vaper, will surely appreciate the ease of use and the robustness of the Adept mod, as well as the good overall aromatic yield of the Zlide, in fact the Adept kit is simple to use as a pod, but much more powerful.

The Innokin Adept with Zlide Kit is designed to be easy to use and I consider it particularly suitable for those approaching cigarette smoking, the suggested retail price is 44.24 euros.

If you decide to buy it, I recommend you add a 0.8Ω coil to the cart, because Innokin has once again chosen for some mysterious reason not to include the best of its resistance in its kit.

For more product information visit the NewVaping website: Innokin Adept Zlide Kit