Introducing the AGA - Hydra and the AGA - Tiamat Rebuildable Atomizer Tanks

[wolandepiphanius]

Mine seemed to fit fine, but you would think that they used a hacksaw to cut them - jagged and chipped. The chipping doesn't show when it is recessed into the top and bottom cap, but I'm sure the o-rings will suffer. Off to IBTanked for some good old American made glass tanks!

I tried again, but it just doesn't fit. But, like I said, I usually get colored tanks for IBTanked. It's no big deal, and it was free anyway.

but I do like the machining on these better than the first AGA-Ts. I haven't used it yet. I'm waiting until the weekend to toast some mesh .

 

[dsy5]

I did wet sand the top and bottom of the glass - at least it is smooth now. I will probably replace it though, with an IBTanked eventually.

 

[wolandepiphanius]

One thing I noticed about the AGA-T+ is that the wick hole is smaller than the previous AGA-T. Did anyone else notice this? Or am I imagining this?

 

[dam718]

So I just bought up an AGA-T+ from Eric, and went ahead and ordered a glass tank from IBTanked as well just to be on the safe side (Don't want any chipped glass in my juice!)

This is my first RBA, so I may be hitting all you pro's up for advice once it gets here Doesn't look too complicated, and everyone seems real happy with these, so I had to give it a try...

 

[gormly]

I did wet sand the top and bottom of the glass - at least it is smooth now. I will probably replace it though, with an IBTanked eventually.

just so you all know there are some duds in the glass order.. some overly edged etc and even some too large (wtheck)..

I have requested better glass cuts, it's coming, with fire smothed edges like they should have been.
I am not sure on ETA. But they are coming, I will try my best to replace any that are really bad, free with any order, but please don't take advantage if you do not need to. I've tested 5 random units and while not a great cut they work fine (but I am aware some do not)

I will post here when I get them, from the new pic it looks like it is professionally done this time.

 

[eHuman]

just so you all know there are some duds in the glass order.. some overly edged etc and even some too large (wtheck)..

I have requested better glass cuts, it's coming, with fire smothed edges like they should have been.
I am not sure on ETA. But they are coming, I will try my best to replace any that are really bad, free with any order, but please don't take advantage if you do not need to. I've tested 5 random units and while not a great cut they work fine (but I am aware some do not)

I will post here when I get them, from the new pic it looks like it is professionally done this time.

Mine works fine too, my only concern (because I did not smooth the tank edges with emery cloth) is the eventual o-ring fail due to the sharp edges being snugged in contact with the o-ring.

 

[Big Screen D]

I see where SmokTech is coming out with a RBA tank. Hear rumors of a Chinese Z-Atty clone. Should I wait on my favorite vendor?

 

[zippersnapper]

Eric:
I'm going to order a AGA-T+ tomorrow..hoping you have at least one glass tank that is somewhat smooth to work with, or are all "pretty rough" ?

 

[dam718]

Eric:
I'm going to order a AGA-T+ tomorrow..hoping you have at least one glass tank that is somewhat smooth to work with, or are all "pretty rough" ?

I know it's just more to mess with... But the IBTanked clear pyrex tank that will be fabulous when you get it, with nice smooth blown edges, is like $11 shipped. Not bad for a glass tank tube...

 

[thedesbois]

I know it's just more to mess with... But the IBTanked clear pyrex tank that will be fabulous when you get it, with nice smooth blown edges, is like $11 shipped. Not bad for a glass tank tube...

What size did you order for the AGA-T+ at IBTanked? I could measure but I'm lazy and wanna be sure. Ask once, measure once instead of mesure twice.

Thanks

 

[dam718]

On their home page go to "Other Tank Tubes" in the left hand menu... One of the 7 products listed in that section is an AGA-T Tube.

That's what I got... I got it in clear with the 1.8mm wall.

 

[thedesbois]

Thanks. Just visited. New products that weren't there last time. Cool! 1.8mm wall makes sense, will hold more liquid.

 

[gormly]

Terminator Mini, Terminator and Terminator-C are all back in stock.

For the Terminator Mini use Code terminator at checkout
For the Terminator use Code terminator at checkout
For the Terminator-c use Code terminatorc at checkout

The top two are the same code.
Note my cart does not allow multiple codes and I have no way around that currently. (sorry)

I can't list the discount but it's significant.

 

[gormly]

I know it's just more to mess with... But the IBTanked clear pyrex tank that will be fabulous when you get it, with nice smooth blown edges, is like $11 shipped. Not bad for a glass tank tube...

Mine will be cheaper although there is no free shipping, still be cheaper even with post.
.

Eric:
I'm going to order a AGA-T+ tomorrow..hoping you have at least one glass tank that is somewhat smooth to work with, or are all "pretty rough" ?

they are all rough for the most part but most are not cut your hand off rough.. just cut somewhat poorly.

 

[WillyB]

Dream Tank (BT804)

No secret code?

 

[Woody-GC]

Dream Tank (BT804)

No secret code?

Try the product code for the discount code, BT804. I have seen that work before.

 

[gormly]

Try the product code for the discount code, BT804. I have seen that work before.

what woody said

 

[WillyB]

what woody said

Cool!

Thanks.

 

[gormly]

Ceramic Wicks are here for those interested

I am packing these in spare CE5 tubes I have so they do not get damaged in shipping. You can order a max of two sets.
If you order two sets all 6 pieces will be in the same tube.

3/32 size:
From what I have been able to summize this one will fit every rebuildable atomizer I sell currently. If you have purchased a rebuildable that can utilize mesh from DiscountVapers, this one will fit.
Please do not email me asking if this will fit, check the hole on your rebuildable if it is 3/32 or larger it will fit

These do not fit the drippers like the Phoenix, I am sure someone can figure it out but they are not specifically made for this.

1/8 size:
This size does not seem to fit any product I have it is too thick, if you have purchased a rebuildable from me, this will NOT fit, you need the smaller size 3/32. Please measure the hole you have to make sure this will fit your device, if your hole is smaller than 1/8th it will not fit. Please do not message me asking if it will fit what you have, if it is not from my store I will not know

My disclaimer for this item:
This product is fragile and cannot handle sheer forces, makes sure you handle this with care. Due to the nature of this product there are no refunds or exchanges.

This includes breakage in shipping, it is far too easy for someone to break one and tell me it came to them broken, if you are not willing to take the risk, do not buy this item.
We are shipping these in CE4/CE5 clearomizer tubes that we have extra of and wrapping them in bubble, in the entire time I have sold vape gear I have had one tube break in shipping because a postal worker decide to stomp on it. I have had a fair amount "crack" but only one outright break. This is the best option I have right now, I am going to try to get some small tube bottles for the future. I am saying this ahead of time, sending me a picture of a broken tube will not be proof they were broken in shipping, I am doing my best to make sure they are shipped properly. You all know me, you know I am fair, but in this case.. this is too new and they are too few in supply.

I wrapped one up, threw it around, dropped a box on it and did everything short of stomp on the package. They were still intact.

This policy may change in the near future as this item gains popularity and volume. For now consider this an experimental purchase.
Please report your experiences by leaving a review.

I will post more when I know more, I asked LD to investigate the sizes, but I need to move onto other things I am sure he has a boat load of things to do, but if I learn anymore I will post it. As of right now I am not sure what the 1/8ths will fit.

 

[Sigaro]

I checked the site, they don't appear to be live yet...