Ithaka and Odusseus compatibility
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
-
- Tags
- provari
- Status
The only way to use the Ody base and not to use BF, is to remove the small set of threads on the bottom of the ceramic holder, as Poppa D said at #111 post.
If you want to remove the Ithaka air flow and keep Ithaka's base, you have to put it in a ggts, or ever better in a JustGG which has even shorter collector tank.
EDIT: ΟΚ... Darkreign was faster
If you want to remove the Ithaka air flow and keep Ithaka's base, you have to put it in a ggts, or ever better in a JustGG which has even shorter collector tank.
EDIT: ΟΚ... Darkreign was faster
The difference between the two bases are 7mm.
I do not think it's worth to take away the air base.
Anyway.. what ever suits you
I do not think it's worth to take away the air base.
Anyway.. what ever suits you
I have been using the Ithaka top caps on my Odysseus and somehow I mixed up the oring on the Ithaka small cap. I have tried so many of the orings and cant seem to find one of the many GG orings that keeps the juice from either spilling out or making the juice come out the bottom. I had no problems until I realized that I somehow got the orings mixed up. If someone could let me know the diameter of the oring that sits under the Ithaka small top cap , Id really appreciate it.
I miss using them.
I miss using them.
Thanks, now off to find the o'rings somewhere. COV is out of them. Im sure with all the orings I have that it must be hiding among them. I keep popping them in to find the right fit and they all leak.
thanks
thanks
I would really love some help, I dont know if its my aversion to numbers or Im really lame, cause I have been searching all the oring sites and I cant find all the numbers to match the 9mm OD x 5mm ID x 5mm C/S , Im also on the lookout for some 4mm OD x ? ID x 1.5 and I cant find that either. Ive tried a few online stores and EBay and find those numbers.
You need 3x1,5 to put it under the center pin of Ody's center post my dear to make your center pole go deeper on its base
ps...... Why do you need 4x.....?
ps...... Why do you need 4x.....?
Umm that 9mm couldn't exist since for an o-ring to have a 5mm cross section it would have to have a min of over 10mm outer diameter. That being said I have a couple 9x2.5 I could shoot you one over if you't like just PM me your address. I have a couple 4x1.5 as well if you want one or 2.
Also this site has them for sale
oringsUSA
When looking for a specific O-rings their orings are grouped by cross section then by inner diameter so all the 1mm cross sections are first then 1.5 2 ect. So if you are looking for 4x1.5 scroll down to the 1.5 cross section O-rings then find the inner diameter. Same with a 9x2.5 scroll to the 2.5 cross section area then find the 9mm inner diameter.
4x1.5 is part number 19153 and 9x2.5 is 19350 hope this helps.
Thanks, for all the good information, everyone. Oh, Imeo I need the 4 x is to replace the oring I lost for my Ithaka small top cap.
I will go and check out the parts at orings USA. Im very very glad for the help. I dont know why , I start to look at all the numbers and my eyes just go crossed.
I will go and check out the parts at orings USA. Im very very glad for the help. I dont know why , I start to look at all the numbers and my eyes just go crossed.
Ithaka's small cap doesnt take 4x o-ring my dear, it takes the 9x2,5 as I told you before
Hey, thanks for clearing that up!Ithaka's small cap doesnt take 4x o-ring my dear, it takes the 9x2,5 as I told you before
- Status
Similar threads
