joyetech Cuboid 150W, Variable Watt/Temperature Control mod in Black
Sure to impress experienced vapers, the Cuboid by Joyetech is an advanced Variable Wattage and Temperature Control mod.
A main benefit of Temperature Control is the ability to avoid burnt or "dry hits" while vaping - this can result from over-heating the coil, or from heating a coil that is dry, due to a low e-liquid level inside the atomizer. In temperature mode, the Cuboid allows you to adjust between 200-600 degrees Fahrenheit (or 100-315 degrees Celsius), and can support the use of Nickel, Titanium, and Stainless Steel wire. In Variable Wattage mode, this mod has a 150 watt maximum output. However, the Cuboid comes with upgradeable firmware - you can upgrade your Cuboid to a whopping 200W by downloading the upgrade software directly from the manufacturer's website here.
A great feature of the Cuboid is that it does not come with a built-in battery. Instead, it offers the convenience of user-replaceable batteries, so you can quickly swap out drained batteries for a pair of freshly charged ones, as needed. The Cuboid is heavier than most mods. But, it is exceptionally well-built and fits comfortably in the hand, thanks to its small size and ergonomic shape. Compared to many advanced devices of its kind, it is very user-friendly, with only two buttons to press and make adjustments with.
The Cuboid has a bright, easy to read 0.96-inch OLED screen with 6-line display. The screen shows your power setting/mode (VW, VT-Ni, VT-Ti, Temp SS316 or TCR), temperature in degrees Fahrenheit, output power (wattage in VT mode, or voltage in VW mode), atomizer resistance in ohms, amperage setting (useful if you are using an RDA/RBA), and finally, a dual battery bar. The dual battery bar is a terrific new feature, allowing you to see the remaining battery life of the individual batteries a glance.
The Cuboid features a stainless steel spring-loaded 510 connection, ensuring that virtually any 510-threaded atomizer will make a secure connection. The Cuboid can accommodate atomizers with a diameter up to ~24mm with no overhang, including the Aspire Triton (22.5mm). However, even wider atomizers like the Kanger Subtank Plus (25mm) look great on it, with the overhang not being very noticeable. The Cuboid is a perfect match with Joyetech's new Cubis atomizer.
The Cuboid is a terrific mod for advanced vapers, who enjoy using temperature control and atomizers using different types of wire builds. The Cuboid features all standard protections, and some innovative features, like the new customized TCR (Temperature Coefficient of Resistance) mode, which advanced users are sure to love. The TCR mode allows vapers who switch between different coil materials frequently to pre-set and save several settings. All the while, you are able to ensure the most accurate and consistent temperature control.
Joyetech Cuboid Features:
Includes:
1 x Joyetech Cuboid 150W mod (High Drain Batteries are not included. You can get these at a discounted price when you select the Make it a Kit option above.)
1 x Micro USB Charge Cable
1 x User Manual and Warranty Card
Size: Height 91.2mm (3.6") / Length 42mm (1.65") / Width 28mm (1.10")
Sure to impress experienced vapers, the Cuboid by Joyetech is an advanced Variable Wattage and Temperature Control mod.
A main benefit of Temperature Control is the ability to avoid burnt or "dry hits" while vaping - this can result from over-heating the coil, or from heating a coil that is dry, due to a low e-liquid level inside the atomizer. In temperature mode, the Cuboid allows you to adjust between 200-600 degrees Fahrenheit (or 100-315 degrees Celsius), and can support the use of Nickel, Titanium, and Stainless Steel wire. In Variable Wattage mode, this mod has a 150 watt maximum output. However, the Cuboid comes with upgradeable firmware - you can upgrade your Cuboid to a whopping 200W by downloading the upgrade software directly from the manufacturer's website here.
A great feature of the Cuboid is that it does not come with a built-in battery. Instead, it offers the convenience of user-replaceable batteries, so you can quickly swap out drained batteries for a pair of freshly charged ones, as needed. The Cuboid is heavier than most mods. But, it is exceptionally well-built and fits comfortably in the hand, thanks to its small size and ergonomic shape. Compared to many advanced devices of its kind, it is very user-friendly, with only two buttons to press and make adjustments with.
The Cuboid has a bright, easy to read 0.96-inch OLED screen with 6-line display. The screen shows your power setting/mode (VW, VT-Ni, VT-Ti, Temp SS316 or TCR), temperature in degrees Fahrenheit, output power (wattage in VT mode, or voltage in VW mode), atomizer resistance in ohms, amperage setting (useful if you are using an RDA/RBA), and finally, a dual battery bar. The dual battery bar is a terrific new feature, allowing you to see the remaining battery life of the individual batteries a glance.
The Cuboid features a stainless steel spring-loaded 510 connection, ensuring that virtually any 510-threaded atomizer will make a secure connection. The Cuboid can accommodate atomizers with a diameter up to ~24mm with no overhang, including the Aspire Triton (22.5mm). However, even wider atomizers like the Kanger Subtank Plus (25mm) look great on it, with the overhang not being very noticeable. The Cuboid is a perfect match with Joyetech's new Cubis atomizer.
The Cuboid is a terrific mod for advanced vapers, who enjoy using temperature control and atomizers using different types of wire builds. The Cuboid features all standard protections, and some innovative features, like the new customized TCR (Temperature Coefficient of Resistance) mode, which advanced users are sure to love. The TCR mode allows vapers who switch between different coil materials frequently to pre-set and save several settings. All the while, you are able to ensure the most accurate and consistent temperature control.
Joyetech Cuboid Features:
- 5-Click the fire button to turn unit ON/OFF
- Variable Wattage, Temperature Control (VT-Ni, VT-Ti, VT-SS316), New TCR Mode
- Variable Wattage: from 1.0 - 150.0 W
- Temperature Control: from 200 - 600 degrees Fahrenheit (or 100 - 315 degrees Celsius)
- Minimum/Maximum Atomizer Resistance: In Variable Wattage mode - 0.1 ohm - 3.5 ohm. In Temperature Control mode - 0.05 ohm - 1.5 ohm
- Firmware Upgradeable: Upgrade to 200W! Download the firmware upgrade from Joyetech's Official Website here, and install after connecting the mod to your computer with the included Micro USB cable
- Dual Removable Batteries: Uses 2 x flat top High Drain IMR18650 batteries (minimum 25A) (batteries are not included with this device)
- Stealth Mode: Vape with the OLED screen off
- Key Lock: Lock the regulatory button to prevent accidental changes
- Atomizer Resistance Lock: Lock in the atomizer resistance in Temperature Control mode to retain temperature accuracy
- Switch OLED Screen Orientation: Rotate the OLED screen display 180 degrees
- 10-second Safety Cutoff: Pressing the fire button for more than 10 seconds will cause the device to shut off
- Atomizer Short Circuit Protection: If an atomizer short occurs, the OLED will display "Atomizer Short"
- Atomizer Low Alert: If the resistance is lower than the specified minimums above, the screen will show "Atomizer Low"
- Reverse Battery Protection: If you accidentally insert the battery cells incorrectly, the device will not turn on to prevent any damage
- Low Power Alert: If battery voltage drops below 3.1V, the screen will show "Battery Low". If you continue pressing the fire button, the screen will show "Battery Low Lock" and will cease output. Please recharge the batteries
- Short Circuit Protection: If you accidentally insert the battery cells incorrectly, the device will not power on to prevent damage
- Temperature Protection: In Temperature Control mode, if the actual temperature of the coil is higher than the set temperature, the OLED screen will display "Protection"
- Temperature Alert: If the device heats up to more than 70 degrees Celcius, the output will shut off automatically and the screen will display "Device Too Hot". Set the Cuboid aside and allow to cool down completely before continuing use
Includes:
1 x Joyetech Cuboid 150W mod (High Drain Batteries are not included. You can get these at a discounted price when you select the Make it a Kit option above.)
1 x Micro USB Charge Cable
1 x User Manual and Warranty Card
Size: Height 91.2mm (3.6") / Length 42mm (1.65") / Width 28mm (1.10")
