Joyetech Evic VT 60 Watt

[JeremyR]

Mines fine, been through some major abuse, heck I even wash it with water..lol.. No problems...

6 out of what 100,000+.. This is not bad..

I really wonder about it just dieing. I have never had this happen on the cheapest of Chinese garbage. Lol

 

[AmandaD]

Well, mine didn't actally die - it doesn't recognize it's plugged in, and so the battery is dead with no way of charging it. The port isn't loose.

 

[USMCotaku]

Well, mine didn't actally die - it doesn't recognize it's plugged in, and so the battery is dead with no way of charging it. The port isn't loose.

Brave enough to pull the top off and make sure a wire isn't loose to the USB port?

 

[AmandaD]

Brave enough to pull the top off and make sure a wire isn't loose to the USB port?

I guess since it's not usable there's nothing to lose by opening it up. But if the wire is loose, then what do I do? (LOL)

 

[USMCotaku]

I guess since it's not usable there's nothing to lose by opening it up. But if the wire is loose, then what do I do? (LOL)

If you aren't up for it, shouldn't be too hard to find someone to solder it back on

 

[USMCotaku]

I guess since it's not usable there's nothing to lose by opening it up. But if the wire is loose, then what do I do? (LOL)

The USB may be directly soldered to the main board, check the solder points, manner sure none are cracked or loose....also look at the wires going to the battery

 

[tchavei]

I guess since it's not usable there's nothing to lose by opening it up. But if the wire is loose, then what do I do? (LOL)

3000W tig welder

Regards
Tony

Sent from my keyboard through my phone or something like that.

 

[USMCotaku]

3000W tig welder

Regards
Tony

Sent from my keyboard through my phone or something like that.

 

[JeremyR]

Most likely the charging cable..

Another one of my old cables failed last night.. Thats two now that won't charge anything.. The one sometimes would charge the cell phone.. But not the mod..

I highly doubt anything is wrong with the mod, the USB is near permanently soldered.. It's not done cheaply I'll tell you that.

 

[AmandaD]

Most likely the charging cable..

Another one of my old cables failed last night.. Thats two now that won't charge anything.. The one sometimes would charge the cell phone.. But not the mod..

I highly doubt anything is wrong with the mod, the USB is near permanently soldered.. It's not done cheaply I'll tell you that.

Definitely not the charging cable. I've tried a half dozen different cables, plugs, locations I wish that was the case, but it appears not!

 

[JeremyR]

Well, mine didn't actally die - it doesn't recognize it's plugged in, and so the battery is dead with no way of charging it. The port isn't loose.

I'll give you 5.00 plus shipping for it, what color?

 

[AmandaD]

I'll give you 5.00 plus shipping for it, what color?

LOL I'm going to take it to my local vape shop and see if they can fix it!

 

[Mrmik]

Got a .12 ohm dual coil build last night on my VCT Mega. 30GA Ni wire 12 wraps 2.5 dia. Vaping at 420F 60W a little warm vape.
Gone through 5 ml as of now and it is just great. Much better than factory standard Ni coils. And the CLR coils are very close in vapor density and flavor.

 

[Mrmik]

The CLR coils are indeed quite nice (haven't even tried the regular prebuilt coils) but I still haven't got them perfect. I've removed the juice control ring, and took off the coil cap as well, but I still can't push the tank as much as I'd like. I have it on 480f on my vaporflask clone (has a more accurate temperature reading) but I get temp limiting at about 20-25w.

How are you coiling and wicking yours?

Sent from my C6903 using Tapatalk

Have not yet done any Ni build on the CLR heads.
Oh my, I just now realized I forgot what GA and how many wraps/dia on those 2 identical .8 ohm builds I have. Have been alternating them, dryburning/rewicking for the past month or more....... Those coils are being used in the Ego ONE XL tank on a 1100mah battery for stealth purposes and portability at work only. Or when I am out and about to stores etc.

 

[coilburner]

Does anyone know how many amps the evic vt is safely capable of putting out?
Also if Im using a coil that reads .57 ohm and 3.84v at 26 watts it should be drawing 6.75 amps right?

 

[atroph]

If you burst 60W into a 0.05 coil you will net 34.64A (VT mode). I don't think many will run that much, but it is designed to do it. I don't think the 3 cell LiPo will have any problem with that.

I=sqrt(P/R)

Your calculation of 6.75A is correct.

 

[KenD]

Resistance doesn't matter with regulated mods. Amp draw is determined by the set wattage and battery charge level (lower charge = higher amp drain), modified by the efficiency of the chip.

Sent from my C6903 using Tapatalk

 

[niterider]

Well, sad morning..took one puff, and my evic died. There is no hard reset for it, right? Any ideas what to do? Nothing happens with all the clicking or if i charge it. Never thought my istick would outlast the evic

Sent from my ALCATEL ONE TOUCH 6033X using Tapatalk

Mine died too or should I say it shorted out and was stuck. Only recourse was to return it for a new one.

 

[atroph]

Resistance doesn't matter with regulated mods. Amp draw is determined by the set wattage and battery charge level (lower charge = higher amp drain), modified by the efficiency of the chip.

Sent from my C6903 using Tapatalk

I disagree.

Resistance, voltage, and current are real. Power is calculated.

Battery charge isn't a good factor either as the mod either bucks or boosts the current battery level. The math gets difficult for rough estimates when you use one part of Pout and one part of Pin.

Efficiency is the ability for the mod to put out exactly what is put in.

It can be calculated by:
Efficiency=Pout/Pin

1 is ideal. Most mods that I have looked at are around 94%+ (or 0.94+).

Not starting an electricity war but your statement is too general and leaves the reader to guess what you mean. Be technical and teach people something. If you generalize and sugar coat the theory you are doing them a disservice.

Sent from my 0PJA2 using Tapatalk

 

[USMCotaku]

He's just saying ohms law doesn't tell you what the amp draw will be on a regulated device....its a watts in=watts out, as your battery drains, to maintain watts out, the mod increases amp draw to make up the difference
Sent with one hand, the other is busy vaping.