Just bought my first ego twist and AIV LBE pack but got some questions

Status
Not open for further replies.

awaw

Full Member
Sep 21, 2013
5
0
Australia
Hey guys i just bought an ego twist with a evod clearomizer as well as a vivi nova tank and a couple of ego dual coil carts.

But was curious since i got the LBE from alice how would i go about trying all the flavours would i fill up the clearomizers then wash the tanks out after im done? or is there a fast way?

I kind of want to just drip a few drops in to get 4-5 puffs to try the flavours.
 

IMFire3605

Ultra Member
ECF Veteran
May 3, 2013
2,041
3,148
Blue Rapids, KS, US
510 or 306 dripping atomizer with a drip tip. Easy to clean out, 4-5 drips of juice, get a few puffs, blow out through the connector end into a paper towel, drip the next flavor in. Just a cup, coil with a little wick in it, at a mouth piece (drip tip) in the case of a 510 drip atty. Really rugged little devices, can last a month each atty with heavy use.
 

awaw

Full Member
Sep 21, 2013
5
0
Australia

dice57

Vaping Master
ECF Veteran
Verified Member
Sep 1, 2013
4,960
3,734
68
Mount Vernon, Wa
Multiple tanks work for me. Quick change vape artist. clean tanks between flavor change is always a good idea. rinsing wick and doing a dry burn also helps prevent flavor crossover. You can also change flavor in a progressive manner such that the next flavor in line for the same tank, isn't messed up by the previous one and enhances it. If I'm to lazy to break down my Russian rba, when changing flavors I'll go from mellow to stronger flavors, like Vanilla > Dulche De Lache > Wacky Tobacky > Super Skunk > Stoned Smurf > Smurf Piss > Virgina Fired Tobacco > Whiskey. Then do a break down, rinse and dry burn, possible an new build if necessary then start some Boba's Bounty. With my build and rba, I only taste the previous flavor for about the first ml of the tank which holds up to 4ml, and doing the progression of mellow to strong, the previous can enhance the current flavor.
 

andervan

Full Member
Jul 14, 2013
43
17
Phoenix Az.
Hey guys i just bought an ego twist with a evod clearomizer as well as a vivi nova tank and a couple of ego dual coil carts.

But was curious since i got the LBE from alice how would i go about trying all the flavours would i fill up the clearomizers then wash the tanks out after im done? or is there a fast way?

I kind of want to just drip a few drops in to get 4-5 puffs to try the flavours.

If you wanna use what you have, you could drip with your Evod.

When I used my Evod to drip: I just unscrewed the tank, and then found the short metal tube with a clear silicone gasket that snaps onto the lower coil assembly. If you apply sideway pressure you'll find that metal tube will pop right off the coil assembly. Do that, and then also remove the short flavor wick you'll find laying on top of the coil (only remove the flavor wick on top, not the second wick that goes through the center of the coil)

Now you could simply drip a couple drops onto the coil/wick, and then screw the tank back on (without reinstalling the metal tube or flavor wick) and vape like 2 or 3 good hits without pouring any into the tank.

Then when your ready to drip the next flavor:
Simply unscrew the tank and carefully rinse the coil assembly off with warm water to remove most all traces of the previous flavor, but just be carful you don't rinse the wick out of the center of the coil. If you can still taste the old flavor with just doing a warm water rinse, you could soak the coil in vodka or Isopropyl Alcohol first, then do a warm water rinse.

You could research the term: "dry burn" here on this forum. and do that in-between dripping each flavor too.

Then when your ready to fill a tank:
Simply clean the coil assembly again, reinstall that flavor wick and press that metal tube back in until you feel it snap back in place.
 

jSquared

Super Member
ECF Veteran
Mar 23, 2013
577
420
London, UK
unfortunately that states it will reduce the lifespan of ego style batteries. Could anyone else chime in on this as it would make things a lot easier for me

Don't let that put you off - they're just covering their behinds! I don't really know why vendors continue to put those kind of warnings on product listings for 2.0 ohm atties, though. It's more relevant if you're using a proper low res atty like a 1.5, but I don't really consider 2.0 ohm to be low res at all. In fact, it's a really good resistance to use on a Twist because even at 4.8V you're still within the 2.5A limit.

Short version: I use 306s on eGos all the time. You'll be fine!

JJ
 
Last edited:
Status
Not open for further replies.

Users who are viewing this thread