Just finished my Poorlin mod!

[mv2envy]

Just finished putting it together and it was no joke! This thing pushed me to the limits! It has almost no room to work with! Major props to mamu for being able to cram everything into this tiny box! It wasnt easy, but I got it done. Didnt put a on/off switch because there wasnt enough room due to the 18awg wires. Also decided to not put a led in there for stealth vaping purposes.
its very pocket friendly! The pot cant be touched by accident and the button is not easy to press by accident. Man is this thing tiny! Its the smallest VV I own at the moment!

Specs

Voltage range 3.5-5.95V
2X AA Charger case (thanks to Mamu for this)
OKR-T/6 regulator
200 ohm pot w/ 220 ohm resistor
Tactile switch using pin 1 (10K ohm pulldown from pin 3)
18awg wires (except pot & tac switch wires)
Nickel plated juice well (finish washer)
Extended 510 connector
2X IMR14500 600mah batts

For size comparison, next no my dual 18650 VV mod (1" x 2" x 4" Radio Shack box)

 

[RIMP]

Very nice

 

[mv2envy]

Thank you!

 

[keyzygirl]

I love it!!Its very nice!!

 

[mv2envy]

Thanks! One of the hardest mods I have built. Very limited room to work with inside (18awg wires didnt help either)

 

[Cool_Breeze]

Looks good!

 

[mv2envy]

Thanks! This thing packs a punch in a small package!

 

[asdaq]

I wouldn't call it poorlin at all. Quite nice actually. Any plans for toggle switches in your next one?

sent from my HTC genisis using Tapatalk

 

[GiMante]

Very nicely done.

 

[mv2envy]

Very nicely done.

Thanks!

I wouldn't call it poorlin at all. Quite nice actually. Any plans for toggle switches in your next one?

sent from my HTC genisis using Tapatalk

LOL, thanks. Toggle switch for what?

 

[breaktru]

Neat MV, very nicely done.

 

[Rocketman]

Very nice, clean lines.
A pair of 14500 cell in there? Wow, that's compact.

 

[mv2envy]

Thanks guys!

Rocket, yes, a pair of 14500's. It is very compact! 18mm x 37mm x 56mm.

 

[surfsuphere]

Reading on phone so hard to see well. Wow so tiny, how do you change the volts? The black knob on top?

 

[coolone1]

Great job!.............

 

[Str8V8ping]

Nice . What did you use on top there around the battery connector ?

 

[mv2envy]

Reading on phone so hard to see well. Wow so tiny, how do you change the volts? The black knob on top?

Yes, the black pot on top. it sits fush with the top of the mod, but it has a cut on it so its very easy to change voltage with your fingernail.

Great job!.............

Thank you!

Nice . What did you use on top there around the battery connector ?

Its a nickel plated #12 finish washer from amazon.com Amazon.com: #12 Countersunk Finish Washers Steel Nickel Plated 100 Pack: Home Improvement

 

[Col. Gaunt]

Very nice, can this handle a dual coil atty or carto?

 

[mv2envy]

Very nice, can this handle a dual coil atty or carto?

It has a 6 amp regulator and I used 18awg wires. It can handle a 1 ohm atty at 6V!!! So yes, it can handle anyting and everything up to 6V

 

[Str8V8ping]

Nice . Iv been looking for a washer like that . Your mod is a lot like mine . Mine uses the same chip with low voltage shutoff and PTC fuse built in .