But its clogged (my atomiser),air tight draw with air holes wide open and it then spill juice through the vent holes
What is wrong or rather,what am I doing wrong?
What is wrong or rather,what am I doing wrong?
Just got a nice UFSv2
- Thread starter martinc
- Start date
- th_trl_thread_readers 0
- Status
Congrats Martin.
Did you set the juice control all the way up so It's closed and then open slightly to set the juice feed rate?
Depending on juice mix it may not take much at all to feed, esp PG.
Did you set the juice control all the way up so It's closed and then open slightly to set the juice feed rate?
Depending on juice mix it may not take much at all to feed, esp PG.
I am a total UFS illeterate here...gotta read on how it works really.
Juice control?
Juice control?
I would like to suggest that you take a little bit of time and go through here:
http://www.e-cigarette-forum.com/forum/gg/237105-instructional-how-video-links-gg.html
here:
http://www.e-cigarette-forum.com/forum/gg/186053-ggts-avs-ufs-user-manual.html
and Here:
http://www.e-cigarette-forum.com/forum/gg/240530-gg-product-illustrations.html
Before you go too much further with your UFS. There is a wealth of information in those threads and relatively easy to navigate that will save you tons of frustation in your journey toward UFS Bliss.
Yeah the UFS has both air control via the ring and juice control by turning the tank counterclockwise to close it and clockwise to open it.
Well there's your problem xD
For starters, before adding the body sections onto the juice control (the base that sits in between the aircontrol tank and the clear section), make sure that your atomizer is screwed EXTREMELY tightly into the atty connection. Then once fully assembled (sans top cap), be sure to close up your air control. Happy vaping!
Yep once dialled in the only thing that beats it is an Ody
Yeah,its a precision tool,had a slight burnt taste and 2 degrees rotation cured it....geez
It has a pretty steep learning curve to it, but once mastered, I think it's just as good as Odysseus,at least until we get extended mode!
It's the only mod of mine that I don't let the girlfriend borrow xD
It's the only mod of mine that I don't let the girlfriend borrow xD
I wonder if the top 2 parts are compatible with the ody...it would only leave 4mm of the mouth piece to protrudes though but heh
What is the best ohms atty to work in there,It seems to always have a slight burnt taste with a 1.5 ohms LR...I do have a 2.6 and a 2.9 and a bunch of 1.9
Edit: I use it on a stealth and a 18350
Edit: I use it on a stealth and a 18350
Mine is currently setup with a 1.25ohm dual coil cartomizer (not punched!), and it's working beautifully. I'd stick with the 1.5ohms until you get the hang of them, but if you can't get them to wick properly, tighten the air control, open the juice control up more than normal, and then take a good, hard, sharp dry pull to re-wet the coil. Shouldn't flood if done properly.
If that doesn't work for you, try the 1.9s. The lower wattage from em will make the wicking process less demanding.
If that doesn't work for you, try the 1.9s. The lower wattage from em will make the wicking process less demanding.
What's best is what works best for you If you're getting burnt taste, you probably just need a hair more open on the juice control. Or you could always try a 2 ohm atty like mentioned above
My personal favorite is a 3 ohm 306 in a 6v setup. The voltage under load on those batteries hits my sweet spot after about a half hour of use.
If you're getting burnt taste, you probably just need a hair more open on the juice control. Or you could always try a 2 ohm atty like mentioned aboveMy personal favorite is a 3 ohm 306 in a 6v setup. The voltage under load on those batteries hits my sweet spot after about a half hour of use.
Good pointers,thanks to all
And about transportation...close both adjusments and all is good?
And about transportation...close both adjusments and all is good?
No they are not Ody is 23mm dia UFS 24 the tank parts are not compatable. As for traveling if you mean air you probably don't want any juice in it as a metal on metal seal will probably not prevent flooding and in turn leaks with cabin preassure. If you mean while you are driving I just leave my adjustments alone all the time but I use cartos and they are much more forgiving with flooding ect IMHO
Love the UFSv2 but Odysseus beats it.
Odysseus less fiddly for me, less prone to flooding and you are not dependant on china atties or cartos..
Wire and wick may not be as readily available, but if you stock up when you can, you can vape out for long time and only need juice.
Almost totally self sufficient vape system. I can't see it getting better than that.
Odysseus less fiddly for me, less prone to flooding and you are not dependant on china atties or cartos..
Wire and wick may not be as readily available, but if you stock up when you can, you can vape out for long time and only need juice.
Almost totally self sufficient vape system. I can't see it getting better than that.
- Status
