Kanger Subtank Nano Pocket Sized Setup

[WickedBad]

Here is my Subtank Nano installed on a Joytech eGo One 1100mah battery. The battery is unregulated so it fires at the current voltage level. Sits really easy in my pocket and has a better capacity than the eGo atomizer. Finish is very close on these two.

 

[Bammer555]

Nice setup

 

[erikbal]

Nice! I would love something that small that still gives a nice vape!

Sent from my VS980 4G using Tapatalk

 

[Maverickdrinker]

Thanks for the pic. I was thinking of purchasing that combo. Looks real clean. Will have to pick this combo up on the weekend

 

[javarivanhans]

Nice pic, thank you for sharing

 

[seniorGecko]

very nice indeed. I just got the same setup. It's weird though, the ego one drip tip does not fit on the subtank. I had thought that all drip tips were the same size :/

 

[rbferg]

The Nano with eGo One battery is my on-the-go setup as well. Great combo!!

 

[crispncrunchy]

Can you guys confirm whether the Subtank Nano screws all the way down on the Ego-One battery? I tried my Mini on the Ego-One and there is about a 1 mm gap between the tank base and the top of the battery. In WickedBad's photo there looks like a bit of a gap.

 

[rbferg]

There is a tiny gap with the Nano screwed all the way down. Its just enough to slip a piece of paper into not 1mm (hardly noticeable). The eGo One battery is around .5mm larger in diameter than the Nano and probably why you notice a gap.

 

[crispncrunchy]

Thanks for that. I did try putting my Mni on the Ego One battery and yes screwed it down to the thickness of a piece of paper as you say. Kind of prefer the vape from the Ego One tank more than the Subtank Mini anyway so no need for me to go buy a Nano.

 

[desrever]

Really digging this setup. Anyone know how this compares to an eGrip with the RBA base? That's currently my pocket setup but love the idea of a slimmer tube mod. The extra wattage would be nice as well. Sometimes I wish the eGrip could give me 5-10 extra watts

 

[TorVader]

I had a major issue with my setup from day-one. I had my Kangertech Nano screwed down flush with the Ego One battery on the first install, but that pushed the center pin on the battery down and it kept on shorting out on me. Joytech's warranty doesn't cover this issue unless I lie. I use a small screw driver to lift up the center pin by prying it up carefully from the edge, and try my best to keep the tank 1mm away from threading down to the bottom to prevent this, unfortunately sometimes the tank gets twisted and I have to go through the whole process again to enjoy my vape. I put this one together as my easy in the pocket vape as well but it's turning out to be flawed. Wondering if there's 1mm thick washers out there that would fit right, I know 19mm (3/4") is one of the standard diameters for washers.

 

[WickedWicks]

The battery is unregulated so it fires at the current voltage level.

According to Phil its regulated (varies depending on resistance)

Here are the numbers: https://www.youtube.com/watch?v=xJbpT5-ZIco&t=35m52s

 

[WickedWicks]

According to Phil its regulated (varies depending on resistance)

Here are the numbers: https://www.youtube.com/watch?v=xJbpT5-ZIco&t=35m52s

Not quite.
Update: https://www.youtube.com/watch?v=KTT6VL1FQVk&t=1m

 

[rbferg]

I had a major issue with my setup from day-one. I had my Kangertech Nano screwed down flush with the Ego One battery on the first install, but that pushed the center pin on the battery down and it kept on shorting out on me. Joytech's warranty doesn't cover this issue unless I lie. I use a small screw driver to lift up the center pin by prying it up carefully from the edge, and try my best to keep the tank 1mm away from threading down to the bottom to prevent this, unfortunately sometimes the tank gets twisted and I have to go through the whole process again to enjoy my vape. I put this one together as my easy in the pocket vape as well but it's turning out to be flawed. Wondering if there's 1mm thick washers out there that would fit right, I know 19mm (3/4") is one of the standard diameters for washers.

I haven't had this problem, but It would be nice if the eGo One battery had a adjustable or spring loaded 510 connection. You definitely shouldn't crank the Nano down completely flush with the battery. There will be a very small gap between the two.