Kayfun from eciggity HELP
- Thread starter DeathBYzombieZ
- Start date
- th_trl_thread_readers 0
- Status
You should be getting everything thats in the picture, IF it's not there it probably won't be there when it arrives. same thing goes with in the description. I'd go through a different company I think,,,,
well here it is on the site Kayfun Lite Plus by Tobeco - Eciggity
says it comes with X1 tobeco kayfun clone but in the picture it shows the screwdriver , allen wrench etc.
I wanna order from this site cause its cheap and reliable from what I've read.
I have the Kayfun 3.1 Clone by EHPRO I bought it @ my b&m paid $ 50 love it
edit:Kayfun Lite Plus Clone by EHPRO
edit:Kayfun Lite Plus Clone by EHPRO
It's a clone. The only thing it comes with is the kayfun...no extra o rings nor screws. I'd look elsewhere.
I can tell you those screws are very tiny...it's easy to drop one and never find it. You need extras.
From the pictures yes it looks like you"ll be getting whats in the box. And if you don't go to home depot or an auto parts store and pick up some little tools. I wouldn't worry.
I received this one today, and it came with everything pictured. I'm very happy with it! Kayfun Lite Clone RBA Rebuildable Atomizer Tank High Quality Fast Shipping | eBay
No it doesn't come with anything but the device. The picture of the one she posted only has the device. The ones with the whole kit is $10 higher.
I have that kit I got it at 101vapes for 32 bucks and 2 bucks shipping. I digress....it comes with 2 wicks a small blue handled screw drive a few extra screws o rings but only stainless steel tank and lots of machine oil. I would say to look at one with the frosted insert tank or the m tank (full clear tank). They will run about 50 bucks this has all three set ups
https://www.free-cigs.com/Kayfun-Lite-Plus-Clone-Ehpro_p_620.html
I have this one too
Last edited:
This is a kayfun lite not a lite plus. Kayfun lite doesn't have airflow control or recessed fill port with o ring. Other then that it the same
Funny I just got that exact Tobeco Kayfun from Eciggity.com in the mail today! It comes with lots of extra o-rings, screws (both deck and air flow hex screws), mini screwdriver and allen key. The thing it doesn't come with is the "clear" middle tank piece. It only has the steel tank sections. I also bought the "m" opaque tank from eciggity and it looks really cool as a "clear" kayfun!
There was one big flaw with my tobeco clone that I had to fix before using! This is going to be hard to explain but on the deck, directly below the air hole there is a thin piece of white delrin separating the negative block from the deck. The delrin was "trimmed" to much and I could see a tiny gap under it. When I blew down through the air hole I could feel air come out of that hole. Not good as I believe I would get leaking through it.
I took the pin out of the bottom, the pieces on top of the deck came off. I stretched a tiny o-ring around the bottom of the delrin and that sealed the hole. I've been vaping on it for the last few hours and it's working good with a 1.6 ohm microcoil/cotton set up on my Sigelei Zmax V3.
I regret not taking photos of the problem and the fix
I should add that other than the problem above the clone is ok. The threads seem good, not buttery smooth but ok. There was a lot of machine oil and it did take a little scrubbing to clean. Also the juice channels seem on the small side. Vaping at 8.5 watts, I could just sense a little bit of burnt taste so I've backed it down to 7.5 and it seems happy. On the whole this is not as good a clone as my EHpro Kayfun lite but it's not bad either.
There was one big flaw with my tobeco clone that I had to fix before using! This is going to be hard to explain but on the deck, directly below the air hole there is a thin piece of white delrin separating the negative block from the deck. The delrin was "trimmed" to much and I could see a tiny gap under it. When I blew down through the air hole I could feel air come out of that hole. Not good as I believe I would get leaking through it.
I took the pin out of the bottom, the pieces on top of the deck came off. I stretched a tiny o-ring around the bottom of the delrin and that sealed the hole. I've been vaping on it for the last few hours and it's working good with a 1.6 ohm microcoil/cotton set up on my Sigelei Zmax V3.
I regret not taking photos of the problem and the fix
I should add that other than the problem above the clone is ok. The threads seem good, not buttery smooth but ok. There was a lot of machine oil and it did take a little scrubbing to clean. Also the juice channels seem on the small side. Vaping at 8.5 watts, I could just sense a little bit of burnt taste so I've backed it down to 7.5 and it seems happy. On the whole this is not as good a clone as my EHpro Kayfun lite but it's not bad either.
Last edited:
One other thing about eciggity...
I got free shipping (2-3 day priority with $100 insurance). I ordered on 02-12. Electronic shipping info was received on 02-14. It sat that way until 02-21 when it finally hit the post office in Hawaii. It then took until today 02-26 for it to arrive. 2-3 day priority mail took 12 days to go from Hawaii to Maine! I'm not complaining as the shipping was free and I wasn't in a hurry but 12 days!! Not at all what I expected!
I am very happy though with my second MVP2 despite the hiccup with the Tobeco...
New Silver one!
I got free shipping (2-3 day priority with $100 insurance). I ordered on 02-12. Electronic shipping info was received on 02-14. It sat that way until 02-21 when it finally hit the post office in Hawaii. It then took until today 02-26 for it to arrive. 2-3 day priority mail took 12 days to go from Hawaii to Maine! I'm not complaining as the shipping was free and I wasn't in a hurry but 12 days!! Not at all what I expected!
I am very happy though with my second MVP2 despite the hiccup with the Tobeco...
New Silver one!
Ok. Well maybe there's an error on their site then. Because that one she posted says it only comes with the device while the others you click on show o rings, wire, screws etc...
Probably because it doesn't come with extra tanksOk. Well maybe there's an error on their site then. Because that one she posted says it only comes with the device while the others you click on show o rings, wire, screws etc...
See...
Kayfun Lite Plus by Tobeco. It has adjustable airflow control and works exactly as the real one. It also includes an adjustable 510 connection. It provides excellent flavor! Definitely recommended! This Kayfun Lite Plus by Tobeco does not come with the clear tank.
Includes:
1x Kayfun Lite by Tobeco
The others have screws, o rings etc listed under includes... So this particular kit I doubt will come with extras. Maybe if you ordered it somewhere else it will, but I doubt it here.
Kayfun Lite Plus by Tobeco. It has adjustable airflow control and works exactly as the real one. It also includes an adjustable 510 connection. It provides excellent flavor! Definitely recommended! This Kayfun Lite Plus by Tobeco does not come with the clear tank.
Includes:
1x Kayfun Lite by Tobeco
The others have screws, o rings etc listed under includes... So this particular kit I doubt will come with extras. Maybe if you ordered it somewhere else it will, but I doubt it here.
- Status
Similar threads
