KFL+...Sloth's Vapourney Continues
- Thread starter Sloth Tonight
- Start date
- th_trl_thread_readers 0
- Status
Hes either sitting in his chair with a slight smile and eyes rolling to the back of his head or hes throwing his KFL against the wall lol
LOL more like talking with the guests and taking a series of phone calls. everything happens at once 
But so far it's door #1 however i'm not smiling yet. It usually takes a few puffs. i've taken a lot more than normal for it to set into dry hits though. its not the greatest wick for sure either way. no crack, pop...kinda smooth, lingering on the sound of a dry hit but that could be psychological too. Vapors good, not as great as i've seen it. same with flavor. then again i've been vaping this flavor for a bit so may be desensitized to it ATM. also not my favorite flavor so it wouldn't exactly make my eyes water but it's good. *vape vape*
But so far it's door #1 however i'm not smiling yet. It usually takes a few puffs. i've taken a lot more than normal for it to set into dry hits though. its not the greatest wick for sure either way. no crack, pop...kinda smooth, lingering on the sound of a dry hit but that could be psychological too. Vapors good, not as great as i've seen it. same with flavor. then again i've been vaping this flavor for a bit so may be desensitized to it ATM. also not my favorite flavor so it wouldn't exactly make my eyes water but it's good. *vape vape*
Keep vaping it dude. They dont always crackle and pop. I wouldnt worry so much as to what its doing or not doing, just how good it tastes 
If youre not getting burnt hits then we've made progress
If youre not getting burnt hits then we've made progress
If that puppy is wicked right, you should be able to hit 4.2 volts without a problem. I like the fact that you took the bump and vape approach. This way, if you push the limit and the flavor starts to go away. you can always bump back a bit.
Keep vaping it dude. They dont always crackle and pop. I wouldnt worry so much as to what its doing or not doing, just how good it tastes
gotcha and i correct myself...not NO pop and crackle just few and far between
I think I'm comfortable saying at this point that it's good to go...but watch as soon as I say that...LOL
yeah I've been taking this approach since my first bout with dry hits. I'll try bumping it up slowly soon. bout to ha an influx of visitors from a historical tour...can't vape out the office too much LOL
gotcha and i correct myself...not NO pop and crackle just few and far between
I think I'm comfortable saying at this point that it's good to go...but watch as soon as I say that...LOL
I know, right. JINX!
Oh man, you're sh!tt'in me! Cover the intake take a non fired pull and let it sit for a second.
Letting it sit now...it was after a few drags on 4 volts. back down to 3.8 gonna stick here for the time being
You guys are great! I'm reading this thread - laughing - and rooting for sloth...
...and thinking - I've had *extremely* good luck...
no drill bits - I use a little 2mm screwdriver (measured it in one of those thingies with the holes) It's easy to wind my wire and push gently against the end of the screwdriver handle.
I keep the coil in the screwdriver when I mount it - when it's lined up where I want it and screwed down tight I twist/bend the extra wire until it breaks. Doing it this way hasn't left any wire poking out from the screws.
I use the screwdriver to *gently* pull up on the coil and leave a bit of room over the base. (mine sit a little lower than the pic sloth posted)
I also mount my coil, check the ohms - then fire it, get it red hot - release the fire button - and then gently pinch the coils together with tweezers. I do that a couple of times.
I fire it several times to make sure it heats evenly from the inside of the coil out and there are no overlapping coils.
I am also officially casting my vote for Sterile Rolled Cotton for my wick. I did a side by side with organic cotton ball and the Sterile Rolled Cotton tastes perfect right from the start. It's also sooo easy to work with, nice long fibers - it just works for me.
Go sloth... go...
...and thinking - I've had *extremely* good luck...
no drill bits - I use a little 2mm screwdriver (measured it in one of those thingies with the holes) It's easy to wind my wire and push gently against the end of the screwdriver handle.
I keep the coil in the screwdriver when I mount it - when it's lined up where I want it and screwed down tight I twist/bend the extra wire until it breaks. Doing it this way hasn't left any wire poking out from the screws.
I use the screwdriver to *gently* pull up on the coil and leave a bit of room over the base. (mine sit a little lower than the pic sloth posted)
I also mount my coil, check the ohms - then fire it, get it red hot - release the fire button - and then gently pinch the coils together with tweezers. I do that a couple of times.
I fire it several times to make sure it heats evenly from the inside of the coil out and there are no overlapping coils.
I am also officially casting my vote for Sterile Rolled Cotton for my wick. I did a side by side with organic cotton ball and the Sterile Rolled Cotton tastes perfect right from the start. It's also sooo easy to work with, nice long fibers - it just works for me.
Go sloth... go...
that's my guess with this build. why do you think I was doing 4 before with no issues? granted it was Wakonda vs PBC so different liquid? coil is 1.6 now vs 1.7 then
i was even doing 4.5 on Wakonda chain vaping like a bat outta hades with a nic fit LOL
+1 for twisting the wire ends to break them off Remie...i just started doing that as opposed to clipping with nail clippers. much easier and cleaner this way
Who knows dude. The ohms of the coil, they way they are wrapped etc all plays a part in it. PBC will burn at higher volts/wattage
Remie, great post! With a pair of ceramic tipped tweezers and a gentle touch, you can pinch those coils together while the coil is fired.
- Status
Similar threads
