KOOPOR MINI

[nasar syammach]

I use a koopor mini ( 60watt ), what is the lowest ohms using a battery 20A, a nice wire used and the appropriate wire sizes, please share this information, thanks

 

[sonicbomb]

With a regulated device the coil resistance is unimportant in terms of how many amps are drawn from the battery. The wattage is what dictates this, with the most amps being drawn when the battery is discharged. A good rule of thumb is 60 watts as a limit for a 20 amp battery (assuming it is really a 20 amp battery), so you are good with your device.

What battery are you using?

What coil you use is a matter of personal preference and the kind of vape you want to achieve. Hot and cloudy or more restricted and tame.

What atomizer you are using, and what wire do you have?

 

[nasar syammach]

With a regulated device the coil resistance is unimportant in terms of how many amps are drawn from the battery. The wattage is what dictates this, with the most amps being drawn when the battery is discharged. A good rule of thumb is 60 watts as a limit for a 20 amp battery (assuming it is really a 20 amp battery), so you are good with your device.

What battery are you using?

What coil you use is a matter of personal preference and the kind of vape you want to achieve. Hot and cloudy or more restricted and tame.

What atomizer you are using, and what wire do you have?

Thanks a lot sonicbomb for your reply, I really appreciate the information you can give on this, please forgive me if there are mistakes in the use of language because I'm from Indonesia and are not proficient in English.
Use LG HG2 , Samsung 30Q and Sony VTC5 A .. is better for me if Hot and Cloudy .. Use RDA Tsunami 22 and RTA Augvape Merlin Mini .. 24 & 26 gauge UD SS316L Wire , 24 & 26 gauge SS 304 , 22 gauge UD Khantal A1 for single coil around 0.28 - 0.35 ohm , Use UD Khantal A1 26 & 28 and 28 gauge UD SS316L for dual coil or sometime use in parallel around 0.25 - 0.5 Ohm ..
Is there any suggestion from you how low that I can possibly accomplish,thanks

 

[sonicbomb]

Those are great batteries (20a, 20a and 25a) so you're good there.
It's very hard for me to suggest a coil because the variables and preferences of airflow, coil position and wicking are highly individual. You should experiment and find what works for you. What's important is you take note of the first sentence in my last post. Resistance is unimportant. Build for maximum surface area and minimum mass, try using steam-engine to model your build paying attention to the heat flux.

You could try some of your 26G 316L SS dual coils at 3mm ID x 12 wraps. Though the Tsunami has a very large chamber and lots of airflow, so it could handle more than 60 watts with this setup.

 

[nasar syammach]

Those are great batteries (20a, 20a and 25a) so you're good there.
It's very hard for me to suggest a coil because the variables and preferences of airflow, coil position and wicking are highly individual. You should experiment and find what works for you. What's important is you take note of the first sentence in my last post. Resistance is unimportant. Build for maximum surface area and minimum mass, try using steam-engine to model your build paying attention to the heat flux.

You could try some of your 26G 316L SS dual coils at 3mm ID x 12 wraps. Though the Tsunami has a very large chamber and lots of airflow, so it could handle more than 60 watts with this setup.

i will try your dual setup , read your blog and learn more about it ..you have a good and nice avatar..thanks alot for your reply and kindness.

 

[sonicbomb]

Glad I could help

 

[Two_Bears]

I use a koopor mini ( 60watt ), what is the lowest ohms using a battery 20A, a nice wire used and the appropriate wire sizes, please share this information, thanks

If memory serves tge lowest resistance is .3 ohm for Koopor Mini

In a mech mod with a 20 amp battery the lowest i would go is .25 ohms.

 

[KenD]

I use a koopor mini ( 60watt ), what is the lowest ohms using a battery 20A, a nice wire used and the appropriate wire sizes, please share this information, thanks

Note that you'll have fairly poor battery life at 60w using a single battery (particularly as the Koopor Mini only discharges the batteries to 3.5v, if my memory serves me). Using a dual-battery mod where you don't max out your batteries will give you more than twice the battery life.

Sent from my M7_PLUS using Tapatalk

 

[djsvapour]

According to the Kooper Website I found, it can fire down to 0.1ohms.

I don't use 24awg anyway, so a nice coil with 26awg would be my choice... which cannot possibly get down to even close!

 

[Two_Bears]

According to the Kooper Website I found, it can fire down to 0.1ohms.

I don't use 24awg anyway, so a nice coil with 26awg would be my choice... which cannot possibly get down to even close!

Had NO idea it could fire that low.

 

[nasar syammach]

If memory serves tge lowest resistance is .3 ohm for Koopor Mini

In a mech mod with a 20 amp battery the lowest i would go is .25 ohms.

Thanks for your reply ..

 

[nasar syammach]

According to the Kooper Website I found, it can fire down to 0.1ohms.

I don't use 24awg anyway, so a nice coil with 26awg would be my choice... which cannot possibly get down to even close!

Thanks for your reply ..

 

[nasar syammach]

Note that you'll have fairly poor battery life at 60w using a single battery (particularly as the Koopor Mini only discharges the batteries to 3.5v, if my memory serves me). Using a dual-battery mod where you don't max out your batteries will give you more than twice the battery life.

Sent from my M7_PLUS using Tapatalk

Thanks for your reply ..

 

[Grego25]

I like .24 kanthal wrapped 7 times around a 1/8 bit (little over 3mm). I get around .31 ohms with dual coils. You can go lower but might not like the results. Like other people said battery life won't be great running your mod at full throttle. I try not to go more than about 75% of rated power


Sent from my iPhone using Tapatalk