Lava tube v1.5 burnt tast with E1 Clearomizer - ReVive - v2 (SR)

[danm219]

When I use the E1 clearomizer 2.5 ohms, vision ego clearomizer 2.2 ohms, and the Kange bottom coil clearomizer with the Lava tube v1.5 I have to set the Voltage to 3.3 and I get a little burnt tast not much. When I use the Ego Twist I can go up to 4.8 volts without any burnt tast but my sweet spot is 4.2. Is this because of the amps ? Lava Tube V1.5 3.2 amps. Twist 2.5 amps. I was thinking it might be because I use 50/50 juice but why would it work on the twist.

 

[Flyer]

The short answer is, if you are getting a burnt flavor, the coil does not have enough juice, the voltage is too high for the coil resistance. When you start getting a burnt flavor regularly, there is a chance that the wick material has also burnt and will now always give a bad flavor.

If, as you said, you have a clearo that tastes good on the Twist at 4.8V and burnt on the LT at 3.3V, I'd begin to wonder if the LT is defective.

 

[SissySpike]

A agree with answer above if your getting a burnt taste at 3.3 on your LT that doesn't sound right. If its a fairly new LT try contacting your distributor it might need replacing. Most are more than happy to assist you and will exchange with out any hassles.

 

[danm219]

when I check the ohms with the LT it changes sometimes it at 2.5 or 2.9 and so on. I put an ce3 bottom clearomizer 2.4 - 2.6 on the LT at 5 volts and no burnt taste with 50/50 juice. I wounder if the 50/50 is too thick for the top coil clearomizers. I still don't understand why they work with the twist.

 

[danm219]

I think that it is the 510 to Ego adapter. When I use the Adapter the oHms are all over the place but when I take it off the ohms stay the same. So is the adapter shorting out the clearomizer?

 

[Flyer]

So, without the adapter, what resistance are you reading?

 

[danm219]

my boge is 2.7 to 3.0 and with the adapter it reads 2.5 to 3.5 ohms without it reads a steady 2.7 ohms.
My ce3 is 2.4 to 2.6 and with the adapter it reads 2.1 to 3.0 ohms without 2.3 or 2.4 ohms

 

[Flyer]

with the boge its at a steady 2.7 ohms and with the ce3 it at 2.3 to 2.4 ohms

No way it should taste burnt with 2.3-2.4 ohms at 3.3V on a LT. At most that is 4.7 watts! Somethings wrong.

 

[danm219]

thats why i think it the adapter because without i can vape the ce3 at 4.2v with no burnt taste as long as i lay the LT on it's side so the juice stays by the atty. but with the adapter I get a burnt taste and the ohms run all over the place.

 

[Flyer]

thats why i think it the adapter because without i can vape the ce3 at 4.2v with no burnt taste as long as i lay the LT on it's side so the juice stays by the atty. but with the adapter I get a burnt taste and the ohms run all over the place.

For the life of me, I can't think of how the adapter could cause this!

 

[danm219]

I can't either but thats what it looking like. As for the burnt taste the vender told me to lay the LT of it side so the juice stays on the atty and that seems to be working so far. I put the stardust on the LT with the adapter and the ohms reading was 0.1 can't try it with another adapter because I only have one. the stardust works just fine on the twist. so process of elimination say it has to be the adapter. some how it has to be shorting the stardust out ?

 

[Flyer]

Well, replace the adapter and see what happens. I can see an adapter having a problem, but not the one you describe.