-
Need help from former MFS (MyFreedomSmokes) customers
Has any found a supplier or company that has tobacco e-juice like or very similar to MFS Turbosmog, Tall Paul, or Red Luck?
View thread
- Status
The only thing I don't care for about it is the size of the bottle. I need to look at it again for how much it holds but I know as much as I go through on my vmod I would bet that little bottle would not last me any time that is if I were to use it on other devices.
But still might try it just because I could use it for juices I want to try out but don't want a huge tank of it.
But still might try it just because I could use it for juices I want to try out but don't want a huge tank of it.
I have juices I love but they aren't ones I want to vape for any sort of extended periods of time. I've been direct dripping them but that is a process I truly detest. My Aurora works great for that purpose.
Anyone use the boiling method with water and vinegar for cleaning the atties? I have done the soaks with isopropyl but I am wondering if the boiling method is better. I have gotten two pretty clean with the soaking but I have one that just seems to be a little more gunked up.
Are you planning on attaching it with the bottle section ? It's ego threaded, no?
From what I've seen you couldn't attach it without it. The mouthpiece section covers the rba and that attaches into the body that holds the bottle. Unless you can screw the rba directly into the vmod and attach a drip tip into the rba itself...
Even with the bottle section, how would you feed it?
I don't think it will work but, you can try...
From what I've seen you couldn't attach it without it. The mouthpiece section covers the rba and that attaches into the body that holds the bottle. Unless you can screw the rba directly into the vmod and attach a drip tip into the rba itself...
Even with the bottle section, how would you feed it?
I don't think it will work but, you can try...
Last edited:
A7 isn't feeding on either my vmod or XL... Any ideas?
306ing it for a little over a week now and like it. Very comparable to the shifu.
306ing it for a little over a week now and like it. Very comparable to the shifu.
It's a little harder to feed with the extension in there. I generally have to tip mine and don't let the bottle get below about a third. Still debating doing the tube mod on mine
I'm having the same problem feeding my A7 also. Does everybody have 1 or 2 extensions on theirs? And still trying to get the cut condom to fit under the screw. I'm wondering if I can find one of my old silicone gaskets that will work, I've got a lot of them, as I take old devices that quit working and rob all the parts I can off of them. Sounds like discovery and tinker time tomorrow!
And I may have a line on a new-used xl, keep my fingers crossed!
And I may have a line on a new-used xl, keep my fingers crossed!
Might be over tightening, sealing off the feed. Place the 510-510 adapter on the a7 first with the O-rings in place, then tighten enough to get it to fire. See how it feeds like that. If there's space between the a7 and shell place a washer or o-ring to keep the shell in place...
The edge of the adapter will, when over tightened, seal off the chamber. Worse case scenario you can notch the outer bottom edge of the adapter to prevent it from sealing..
Or sand the entire outer lower edge of the adapter at an angle... not too much because you still want the inner vmod o-ring to seat against the outer edge of the adapter... You have a couple mm's to work with..
Last edited:
Who me? Heck I have fun everyday, long as I can wake up and see sunshine instead of fire, smoke, little demon thingys running around saying "we've been waiting for you".
I haven't actually boiled the atomizers...but I did put a pretty good bit of water in a pyrex bowl and nuked it until it was good and steaming (but not really bubbling) dropped them in there, then used the carto cleaner thing from Smoktek (Cartomizer/Atomizer Cleaning Kit - With 10ml Control Syringe, Luer-lock compatible w/cleaning tubes and instructions) to "shoot" the really hot water through each atomizer a few times (attaching the hose thingy to the threaded end). Then I soaked them as usual in the isopropyl (doing the whole blowing out thing at each step of course). Did one repeat of the whole procedure and then let them dry about 36 hours. Seems to have worked even better than just rinsing in hot water. I suppose to REALLY do a bang up job...put some vinegar in the water. I forgot about doing that...probably a good plan!
I thought about one of these too but then I ran across this thing at wally world. It works great, was considerably cheaper (when you add shipping) and got my atomizers really clean.
I'm like you fourth, I heated some distilled water in the microwave, pushed that through, then pushed some isopropyl alcohol, then water again. Put them on the window sill that gets a lot of direct sun for 2 days, then vape away. Isn't tinkering great?
Nothing for Lloyd from " The Shining" huh? anyway...
wanted to clarify that I don't mean sand or notch the threaded 510 connection on the adapter but, the bottom widest outer UN- threaded edge..
You never know...
Last edited:
The book's definitely worthwhile. I'd give the movie a pass though.
- Status
Similar threads
- Locked
- Locked
