Limitless RDTA help. Burnt taste each time

[bsidb]

Id try that staggered with a larger inner diameter or 1 less wrap , but that's just from here, whats the resistance of it

 

[Colonel_Black]

Id try that staggered with a larger inner diameter or 1 less wrap , but that's just from here, whats the resistance of it

Unfortunately i don't have any tools to alter the inner diameter. Currently it's at 0.148Ohms on 80W

 

[bsidb]

what do you get like 1 decent puff before a dry hit?

 

[Colonel_Black]

what do you get like 1 decent puff before a dry hit?

No, it's always straight from the get-go that it tastes like really bland and a cotton taste.
I've only ever made one decent coil/build in 30 attempts, haha

 

[bsidb]

I just realized what was missing , you didn't fire the coil before you put the cap on, drip the juice till its wet, fire a couple times while blowing on coils , drip again, fire a couple times while blowing on the coils do this four times about then drip before putting on cap and vape should get rid of cotton flavor at start @Colonel_Black at about 30 watts , work your way up slower without wick going dry

 

[t8kiteasy]

I have the limitless and it works flawlessly. Are you sticking something down thru each channel after fitting top cap to allow for the juice to wick properly??
You can use something small just slide it down thru each channel between cotton and the wall of top cap.
That will allow for air to escape with each vape and wick the cotton properly. I use ko gen do cotton you can get a 200 pack of it from FT for $9.00.

 

[Don29palms]

When I wick a coil I drip juice on the coil a lightly pulse it. You can see the juice go into the coil. Keep doing that until you see the cotton outside the coil getting saturated.

 

[THOMAS CAMPAGNA KUNRATH]

Firstly, did you work the hotspots out? Try spacing the coils.. Also, your cotton looks too long, I don't see mine thru the glass once I've got all set. I've never done so long cotton like this and I don't get dryhit with dual ss clapton 26/30 around 100w..

Coils are not well spaced in this picture, but it might help you..

Sent from my LG-D855 using Tapatalk

 

[THOMAS CAMPAGNA KUNRATH]

Firstly, did you work the hotspots out? Try spacing the coils.. Also, your cotton looks too long, I don't see mine thru the glass once I've got all set. I've never done so long cotton like this and I don't get dryhit with dual ss clapton 26/30 around 100w..

Coils are not well spaced in this picture, but it might help you..

Sent from my LG-D855 using Tapatalk

 

[t8kiteasy]

Like I said as long as you create a space between cotton and the top cap to allow air to escape and allow for wicking you should not get any more dry hits.

 

[Chodi]

The one comment I did not see here is that you are supposed to juice up the cotton before putting it through the holes or applying any heat to the coils. The wick should be very wet before you ever heat them. Comb out the tails very well before you juice them they look too thick in your photos. If you are getting bunt hit from the start you should lower your temp to 30w and work you way up 5w at a time until it is wicking at a comfortable temperature. I don't think your problem is the selection of cotton. After you get everything set before you apply any heat let the tank sit for 20 minutes with the wicks soaking in the juice. Then slowly ramp up the temp.

 

[DP2Raja]

If you prime/soak the wicks you will not need to let it set at all. Once you soak them from the juice bottle they will continue to wick naturally. I always slide a wire or a toothpick down the side of the WET wick, between the wick and the deck hole. In between vapes just tilt the tank over to re-wet the wicks. The limitless should run great with no dry hits.