Subscribe to this thread http://www.e-cigarette-forum.com/fo...s-bottom-feeder-atomiser-official-thread.html
one sold on ebay recently for $325.
one sold on ebay recently for $325.
Mechanical reos will be seeing some upgrades
- Thread starter redeyedancer
- Start date
- th_trl_thread_readers 0
- Status
Just got the kit installed. 20 minutes tops and she got a bath.
Are you ready for this?
Omega Clone .39 ohm dual coil
Sony VTC4
4.2 volt UNLOADED
3.92 loaded
3.74 at the posts
.18 voltage drop !!!!!
Sparking like a ..... Used my metal file for my old contacts to make sure the top of the battery was clean. Bottom was perfect.TRA SL Grand
Other than the sparks HOLY @$!#.
Sent from my SM-N900V using Tapatalk
Are you ready for this?
Omega Clone .39 ohm dual coil
Sony VTC4
4.2 volt UNLOADED
3.92 loaded
3.74 at the posts
.18 voltage drop !!!!!
Sparking like a ..... Used my metal file for my old contacts to make sure the top of the battery was clean. Bottom was perfect.TRA SL Grand
Other than the sparks HOLY @$!#.
Sent from my SM-N900V using Tapatalk
Ok I have a question. Those green batts I've seen posted the past few pages they are really too long right ??? I took my door off and looked at my Reo at about the same angle and I see way more spring with my AW IMR's
Is the sparking to be expected, or do we need to do something to eliminate that? I'm fine with it as long as it's not going to hurt anything, but I wanted to be sure.
I tightened the nipple as much as I'm comfortable with (using needlenose pliers and a screwdriver in the 510 connection) but I just checked and all three of mine are putting on a light show. I'm using brand new VTC5s at the moment, but my AW 1600s do it as well.
The difference is insane though. I wrapped two of mine with my usual .6-.7 and they are seriously cooking. I wrapped a 1 ohm for the third and it's hitting better than my old ones did at .6-.7. I think I'm going to have to find a new resistance target a little higher than I'm used to wrapping!
I tightened the nipple as much as I'm comfortable with (using needlenose pliers and a screwdriver in the 510 connection) but I just checked and all three of mine are putting on a light show. I'm using brand new VTC5s at the moment, but my AW 1600s do it as well.
The difference is insane though. I wrapped two of mine with my usual .6-.7 and they are seriously cooking. I wrapped a 1 ohm for the third and it's hitting better than my old ones did at .6-.7. I think I'm going to have to find a new resistance target a little higher than I'm used to wrapping!
ok just curious cause in the pics they look way too long
They do don't they. They're almost identical side by side in my 4 bay charger though.
I rebuilt 2 of mine and using vtc5 sonys. No sparking at all from either one. I didnt crank down on that connector either. Just got very snug and let it go at that.. Moved the firing pin to the correct position under the button and everything is fine.. Dont know why youre seeing sparks.. Hopefully someone else does.
.9 but now i need about 1.2 or so i think.. lol
its hitting so much hotter now with the new so kit inside..
Curses! I've been browsing the site all day looking for something that said "sub-ohm" or similar and instead they were there the whole time, until they sold out and I figured out what I should be looking for. 
I'm not sure I'm smart enough for to shop for Reo accessories!!
I'm not sure I'm smart enough for to shop for Reo accessories!!
I tightend the 510 feed tube as much as I dare. Sparky spark spark spark. But, it is not affecting the performace.. looks like I need to drop my nic again, holy nic buzz batman.
Sent from my SM-N900V using Tapatalk
Sent from my SM-N900V using Tapatalk
When you put your centre post in I wonder if maybe it is sitting too low. Take your atty off very gently push upwards on your feed tube. It won't have to move much but it may be your issue.
just installed 3 kits and I'm lung burning like a mad man. So nice to get this performance from my reo
This is driving me nuts.first I didn't get it tight enough, vape was off so I tried to tighten up .when I tighten up the nipple to the post and I'm not over tightening it.. Barely enough to get the other part screwed on.. It makes the thin white gasket flake up around the head of the screw and then of course you can't put an atomizer on it. I am on my third thin gasket now, ruined two of them. What am I doing wrong? I watched the video a dozen times.
Sent from my SCH-I535 using Tapatalk
Sent from my SCH-I535 using Tapatalk
Here's mine
OLD Kit:
1.21 Ohm Coil
Battery 4.20
Under load 3.76
0.44 drop
New Kit:
1.21 Ohm Coil
4.19 battery
4.00 under load!
0.19 drop!
AMAZING!!!!!!!!! Thanks Rob for going above and beyond!
OLD Kit:
1.21 Ohm Coil
Battery 4.20
Under load 3.76
0.44 drop
New Kit:
1.21 Ohm Coil
4.19 battery
4.00 under load!
0.19 drop!
AMAZING!!!!!!!!! Thanks Rob for going above and beyond!
Curses! I've been browsing the site all day looking for something that said "sub-ohm" or similar and instead they were there the whole time, until they sold out and I figured out what I should be looking for.
I'm not sure I'm smart enough for to shop for Reo accessories!!
Use the "notify me" button to send you an email when more are in stock?
T
- Status
