- Status
I actually run a silly long 3ohm 30awg micro on my VVG cranked up to maximum jiggawatts. Very nice. Instant heat, warm vape, and huge flavor.
It is my NEMP box
Sent from the zoo using Tapatypo 2
Introducing the magic tower of power
Weighing in at .5 ohms and sporting more ribbon than you can shake a fist at......
Toughest build I have done and I thought it would be a complete flop.
Boy was I wrong, unless you are looking for clouds.
Knocked the back out of my throat and devastated my taste buds!
Vapor production seems about the same as a .9 ohm of single magic, weird.
Also a little slow in response.
Weighing in at .5 ohms and sporting more ribbon than you can shake a fist at......
Toughest build I have done and I thought it would be a complete flop.
Boy was I wrong, unless you are looking for clouds.
Knocked the back out of my throat and devastated my taste buds!
Vapor production seems about the same as a .9 ohm of single magic, weird.
Also a little slow in response.
Took 2 turns off each coil for a composite 0.4 ohms which made for fast response.
Time delay gone, but with 4.14V unloaded I get 3.44V loaded for a 0.7V drop.
Going to have to do a firing pin mod at the least to go with my fuse mod.
Also separated the coils which reduced the throat hit, increased vapor, but didn't reduce flavor.
Time delay gone, but with 4.14V unloaded I get 3.44V loaded for a 0.7V drop.
Going to have to do a firing pin mod at the least to go with my fuse mod.
Also separated the coils which reduced the throat hit, increased vapor, but didn't reduce flavor.
The Meat Grinder there has become an all day favorite for my NEMP. Bravo Mr. Mundy!
Atomizer ohm meter
http://www.empiremods.com/product_p/acmetr.htm
Just in case you were looking for one.
Sent from my SGH-M919 using Tapatalk 4
http://www.empiremods.com/product_p/acmetr.htm
Just in case you were looking for one.
Sent from my SGH-M919 using Tapatalk 4
Mundy's Meat Grinder after a couple days of NEMP
Sent from the zoo using Tapatypo 2
Sent from the zoo using Tapatypo 2
Introducing Vertigo:
Gonna be a tough cookie to re-wick!
holy MOG! do you wear chain mail when vaping that...
... or just wrap a coil around it?
27 ga Kanthal A1 wrapped around the .055" mold on the darkzero coil jig.
Fuse instead of spring = no arcing = no noalox = happier Russ
.
Got a little stealth mod. It's quite nice, rocking the reo all day but it's nice to switch it up.
Don't mind the ugly coil.
That leg is far from touching. It's the angle of the picture.
Don't mind the ugly coil.
That leg is far from touching. It's the angle of the picture.
Not a micro by definition... Coils arent touching, but i'm gonna post it here anyways!
Ok... I felt it was time for a new Xobe original coil!
I present you with the Dirty Monkey Steam-Roller
Mundy's magic on a 400 mesh core wrapped in a 400 mesh skin.
Meters at approximately .4ohm
I would not suggest this to the coil newbie! I blew a few fuses getting it right
Sent from the zoo using Tapatypo 2
Sent from the zoo using Tapatypo 2
Ok... I felt it was time for a new Xobe original coil!
I present you with the Dirty Monkey Steam-Roller
Mundy's magic on a 400 mesh core wrapped in a 400 mesh skin.
Meters at approximately .4ohm
I would not suggest this to the coil newbie! I blew a few fuses getting it right
Sent from the zoo using Tapatypo 2
Sent from the zoo using Tapatypo 2
that is on a fully stock mod w/ spring and SS pin. stand fast. I'll toss it back on my fused mod w/ brass pin
- Status
Similar threads
