So what would 2, 1.6mm and 1, 1mm hole equate to ? Where can I find this on my own is there a formula to figure it?
-
Need help from former MFS (MyFreedomSmokes) customers
Has any found a supplier or company that has tobacco e-juice like or very similar to MFS Turbosmog, Tall Paul, or Red Luck?
View thread
Micro Coils to increase Vapor, flavor & TH
- Thread starter super_X_drifter
- Start date
- th_trl_thread_readers 0
- Status
So what would 2, 1.6mm and 1, 1mm hole equate to ? Where can I find this on my own is there a formula to figure it?
After asking and then actually thinking about it, I figured it out. Guess I had a taking care of a screaming baby moment. Lol
Actually drilled the outer 2 hole to 1.6mm, huge difference in vapor and flavor. I just thought is a fog machine before. Actually got kicked out my living room by the wife BC of how big the vapor is now.
Actually drilled the outer 2 hole to 1.6mm, huge difference in vapor and flavor. I just thought is a fog machine before. Actually got kicked out my living room by the wife BC of how big the vapor is now.
That's what I'm guessing too. I love the A6, though mine is the 2 post version instead of the 3 post pictured.
Sent from my LGL55C using Tapatalk 2
Finally got some 32ga a1 kanthal in and tried making one of these for my vivi ... WOW 
works as advertised 
sorry had to be done ... also i have a bit of a head rush from the nic and that hasn't happened sense I switched to vaping. Now to make the wife one maybe this is what will finally make her able to make the switch from analogs.
HUGE thanks to OP and everyone else that has added to this thread!!!!
works as advertised sorry had to be done ... also i have a bit of a head rush from the nic and that hasn't happened sense I switched to vaping. Now to make the wife one maybe this is what will finally make her able to make the switch from analogs.HUGE thanks to OP and everyone else that has added to this thread!!!!
It's from ..........co.uk. I saw it in Todd's review. A mini dual coil dripper. Small diameter. Works great but if you like stiff draws. I do so it works for me.
Continuing the botched Coop(manufacturer mistake). I got bored over the weekend and made a couple measurements and decided to hack up on of the atty's(chimbus) I recieved. Here is the results. The one on the right is the one that I only enlarged the outer 2 holes, from my posts a page back or so. The left is the new modded version of it.
Which one vapes better? Have you done a side by side at same resistance? I'm wondering if the smaller chamber adds anything.
yes, yes. do tell. Chamber size and shape. Sometimes I feel like it makes a huge difference. Other times I'm not sure.
oh, and how did you go about it?
oh, and how did you go about it?
For the differences between them, the smaller one obviously is a warmer vape. In my opinion the amount of flavor is far more pronounced in the opposing sides compared to side by side. The vapor is about equal but just a hair more on the smaller one. One observation is how the small changes in the height of the coil in relation to the air hole is crazy different. With the bigger one you can move it up or down more and achieve a smaller change, where as with the smaller chamber if you move it a hair the change is far more drastic.
As for hkw I did it I just measured how tall the chamber was and where the Irholes were and the top of the post under the cap were and used my trusty dremel with a cut off wheel and cut it off. Smooth the edges with a different wheel I have and chamfered the bottom edge to save the orings when taking cap on and off. Then finally measured the deck and coil height after I made them marked them and tapped a nail where I wanted to drill and drilled. I cut off close to 10mm total off the bottom. Its not the prettiest mod but its only a 6 dollar Atty so I don't really care that much.
Hmmmmmmmm. I've never tried opposing air holes in an atty i liked (afraid to ruin a good thing). More flavor, huh? hmmmmmmmmmmm. But let me make sure I've got this straight. The opposing air hole one is simultaneously the small chamber? (I think you said you got 3, total)
Hey, I know! Can you switch the holes?
you know. Put the holes from the little one on the big one?
you know. Put the holes from the little one on the big one?
Hey, I know! Can you switch the holes?
you know. Put the holes from the little one on the big one?
not really bc the top cap is what i cut in order to make the opposing airhole one, I could switch the caps but 1 side wouldnt get any airflow over the coil.
I also think the opposing airholes creates a swirl effect under the hood compared to having the holes on the same side. Also I only got 2 of them
Last edited:
I saw a roadrunner episode once, where they kept moving this hole around and falling in it. Can't you just switch the holes like 'at?
I didnt bring the atty with the holes on the same side with me to work or else I would mess with it, but I dont think it would work out very good
Too funny, I was at the hardware store and when I asked for a 1/16th drill bit he asked me, "are you cutting wood or metal?"
Uhhh lol.
Uhhh lol.
Last edited:
- Status
Similar threads
- Locked
