That is true, the legs don't glow at all with tightly wound coils (but of course they do get hot). I have ben running tightly wound micro & mini coils in all my RBAs & on none of them do the legs glow. But on my RSST the coil in it now is not tightly coiled & one leg does glow. I've been meaning to make a new coil for it but I don't use it all that much.
-
Need help from former MFS (MyFreedomSmokes) customers
Has any found a supplier or company that has tobacco e-juice like or very similar to MFS Turbosmog, Tall Paul, or Red Luck?
View thread
Micro Coils to increase Vapor, flavor & TH
- Thread starter super_X_drifter
- Start date
- th_trl_thread_readers 0
- Status
Here's another try at it , this time cheesecloth, my XC 116 isn't going to fit in there I think.
This one works much better.
I had some extra wire under the positive screw, I carefully pulled it out some more and lowered it a bit, really good now. It's really close to the air hole now.
This one works much better.
I had some extra wire under the positive screw, I carefully pulled it out some more and lowered it a bit, really good now. It's really close to the air hole now.
Last edited:
Hoosier Vapes has Igo-W's for 16$ I just ordered one.
Edit:
I asked to confirm if they were the dual air hole top caps and they said they were.
Edit:
I asked to confirm if they were the dual air hole top caps and they said they were.
Last edited:
Agreed. I like to get the coil right up to the air hole. For me excessive wick doesn't do anything except prevent leaking on certain RBAs. All that juice doesn't really make it to the coil anyway, although rolled cotton does the best job at it. For Ekowool the excess wick is just a mop.
A short rolled cotton wick will suck up everything in the well. In the second pic the well was full with juice & the cotton sucked it all up.
That's a good lookin coil right there.
the xc 132 fits great in a 1/16" wrapped micro. It takes some serious faith. Wet the tip, light pressure, and corkscrew as far as your fingers can in one go. This should get it lodged just far enough so it won't fall out. Then you can twist away to get the rest. (oh, and twist with the "thread" of your coil, not against.)
Last edited:
In my 100000 experiments experience gauze or cheesecloth will feed until bone dry. If they touch the coil I can taste the cloth on each, I always coil use ss mesh with spliced cheesecloth feeding out of each end, not in coil area really quick feed.. Cottonballs are greedy and keep juice, they do a decent job but will not run feed my micro ss hybrid to bone dry..
Agreed. I like to get the coil right up to the air hole. For me excessive wick doesn't do anything except prevent leaking on certain RBAs. All that juice doesn't really make it to the coil anyway, although rolled cotton does the best job at it. For Ekowool the excess wick is just a mop.
A short rolled cotton wick will suck up everything in the well. In the second pic the well was full with juice & the cotton sucked it all up.
Beautiful coil DZ, do the length of the tails raise the resistance, compensated by fewer wraps ?
the xc 132 fits great in a 1/16" wrapped micro. It takes some serious faith. Wet the tip, light pressure, and corkscrew as far as your fingers can in one go. This should get it lodged just far enough so it won't fall out. Then you can twist away to get the rest. (oh, and twist with the "thread" of your coil, not against.)
When you say xc132 pdib do you meen ekowool ?
No, sir. xc 132 is Nextel it is the smaller diameter version of what we call xc-116. It is a "braided ceramic rope"
EmpireMods also has the version with 2 air holes for $14.
Sent from my LGL55C using Tapatalk 2
May I suggest DUAL MICRO COILS for this purpose?
One of my "benchmarks" for getting a good vape is when the exhale obscures my line of sight of my laptop screen (usually just momentary). This bad boy is just ridiculous, not only is my los obscured it stays obscured for several seconds. I am finding myself either exhaling some other direction or clearing away the clouds with a few waves of my hand.
Hey Statistic, what are you wrapping those coils at? I've tried dual coil micros and can't seem to get enough heat quickly enough to produce a satisfying vape. Was using 28 guage in my Trident wrapped to 1.5 ohms each at 1/16", giving an effective resistance of .7 ohms or so.
Neck 'n neck. It comes down to application. In my goosebox, where I don't need more than coil-filler, I swear by the sterile cotton balls. If you're wanting some wicking action, you could go with the nextel.
Enough of this "shopping" chit-chat. As my little RM2 has only the two posts, I ran my dual coils for the day on the same wick.
and dressed it up like a foppish old Brit.
With mustache wax . . . . . .
"I mustache you a question . . . . "
" . . . . but I'm shaving it for later"
and dressed it up like a foppish old Brit.
With mustache wax . . . . . .
"I mustache you a question . . . . "" . . . . but I'm shaving it for later"
Damn. I should've shopped around a bit lol. I only checked 3 sites. Two had listed around 25$ I didn't figure I would find cheaper than that.
Oh well. It should be here Tuesday along with some square braid cotton wick from Amazon.
Oh well. It should be here Tuesday along with some square braid cotton wick from Amazon.
My octopus clone should be here by Tuesday- Wednesday. I have the rolled cotton from cvs... I have 32 ga kanthan... And a hankering for some micros..... Waiting impatiently lol
Enough of this "shopping" chit-chat. As my little RM2 has only the two posts, I ran my dual coils for the day on the same wick.
and dressed it up like a foppish old Brit.
Swg, ohm's, dia etc ???
- Status
Similar threads
- Locked
