Anyone have a spare RM2 cap with stock airholes or is willing to trade me for one with a 2mm hole drilled out?
-
Need help from former MFS (MyFreedomSmokes) customers
Has any found a supplier or company that has tobacco e-juice like or very similar to MFS Turbosmog, Tall Paul, or Red Luck?
View thread
Micro Coils to increase Vapor, flavor & TH
- Thread starter super_X_drifter
- Start date
- th_trl_thread_readers 0
- Status
They probably won't line up right.
He drills the hole as the triangle atty it is adapted from has another piece where the air hole is.
The threading is not standard in the start point from what I understand.
However for 10 clams you can get the un modified triangle, drill your own, and have spare parts left over.
Triangle Stainless Steel Rebuildable Atomizer
Last edited:
They probably won't line up right.
He drills the hole as the triangle atty it is adapted from has another piece where the air hole is.
The threading is not standard in the start point from what I understand.
However for 10 clams you can get the un modified triangle, drill your own, and have spare parts left over.
Triangle Stainless Steel Rebuildable Atomizer
I effing love you guys. Bunch of walking, talking, vaping dictionaries.
Tried my hand on dual coils for the first time.... Ay dios mio. .. my taste buds are having an orgasm, warmest vape I have ever had... Dual Micros 30 ga, 8/9 wraps on a large paperclip.... Not gonna lie, worried about battery blowing up, wife left the room...lol... first time jitters
Sent from my VS980 4G using Tapatalk
Sent from my VS980 4G using Tapatalk
Good for you, Merlin. Stay a little worried and keep your face in place. 
What kind of batteries?
What kind of batteries?
Thanks pdib. I use MNKE's for 18650 and AW for 18350 ... Now, if I could only be brave enough to try Mundy's Meatgrinder
I'm running 2 - 28g, 14/15 wrap, 2mm wide, micro's on a IGO-W right now with cotton wick and Tasty Vapor Atomic Cinnacide 12mg. It ohm's out at 1.3 ohms and works FREAKING AWESOME on my Vamo (@ 12-13 watts) or unregulated mech. So, 28g is doable, but you end up with a huge coils to get above sub-ohm. The next build I plan on using 30g to see if I can reduce the size because it does take a lot of battery drain to kick start that large of a coil.
Hope that helps.
You admittedly stated you did use unboiled with no issue.
Boiling doesn't make it not burn or change it from cotton to something else. Only clean it of any residue. Which is fine but. Your issue was likely you used too much cotton. Boiled cotton would have given you the same result. The substitute can be trick. Just remember no shoulders after you soak it!
Last edited:
Made something to check resistance easier today. Also gives me a stable place to mount the coils on the atomizer instead of mounting them while they are on my mechs.
And I can still use the leads
And I can still use the leads
To be fair, I saw someone else do this so I ripped off their idea. If you have any questions on how to do it, ask away. Ill try to help as much as I can.
Micro coils are the standard for me. I don't even dare make a coil that is not a micro coil anymore, on any rba/rda/clearo.
I couldn't get a kayfun or russian 91% at the moment, so I got a pair of AGA T2 gennys. However, I was looking for that dripping-like taste and minimal juice cooking inside the tank. After probably 15 hours of tinkering with both SS Mesh and Cotton, trying different methods and whatnot, I gathered all that info and tried something keeping the idea of bottom feeding. I can't imagine this not having been done before, but it sure tastes almost like dripping.
Horizontal micro coil with cotton making contact with two wick holes but not going down in the tank. Adding a small cotton bed underneath the coil long enough to reach the two wick holes as well minimizing leaking and allowing you to vape longer without having to tilt. Vapes like a champ.
PS: I refined that build to where there's not that much cotton and it's really tucked underneath the coil. Works best that way.
I couldn't get a kayfun or russian 91% at the moment, so I got a pair of AGA T2 gennys. However, I was looking for that dripping-like taste and minimal juice cooking inside the tank. After probably 15 hours of tinkering with both SS Mesh and Cotton, trying different methods and whatnot, I gathered all that info and tried something keeping the idea of bottom feeding. I can't imagine this not having been done before, but it sure tastes almost like dripping.
Horizontal micro coil with cotton making contact with two wick holes but not going down in the tank. Adding a small cotton bed underneath the coil long enough to reach the two wick holes as well minimizing leaking and allowing you to vape longer without having to tilt. Vapes like a champ.
PS: I refined that build to where there's not that much cotton and it's really tucked underneath the coil. Works best that way.
I threw together a 1.7ohm micro for the missus so she can drip at home. Ordered her a magneto so I can drop the res down for her later.
She's really enjoying it.
Sent from my SAMSUNG-SGH-I317 using Tapatalk
She's really enjoying it.
Sent from my SAMSUNG-SGH-I317 using Tapatalk
Micro coils are the standard for me. I don't even dare make a coil that is not a micro coil anymore, on any rba/rda/clearo.
I couldn't get a kayfun or russian 91% at the moment, so I got a pair of AGA T2 gennys. However, I was looking for that dripping-like taste and minimal juice cooking inside the tank. After probably 15 hours of tinkering with both SS Mesh and Cotton, trying different methods and whatnot, I gathered all that info and tried something keeping the idea of bottom feeding. I can't imagine this not having been done before, but it sure tastes almost like dripping.
Horizontal micro coil with cotton making contact with two wick holes but not going down in the tank. Adding a small cotton bed underneath the coil long enough to reach the two wick holes as well minimizing leaking and allowing you to vape longer without having to tilt. Vapes like a champ.
PS: I refined that build to where there's not that much cotton and it's really tucked underneath the coil. Works best that way.
This is how ive been running all my Gennies. People may think Gennies are obsolete what with the boom of kayfun-style atties, but i like the separate chamber of a Genny, more options to customize, more builds to play with, more room to manipulate.
I gotta say, I really like checking my resistance on the mod. So many shorts are created at the 510 connection, or internally (in the atty) when that compression is applied. Not sayin', just sayin'.
Got some pics:
Attachments
^ nice build. If you have any issues with flavor, remember the "less is more" wick theory. Good job
^ thank you. We have an awesome group of enthusiasts here. I'm very proud to be among y'all .
.- Status
Similar threads
- Locked
