Mini T3 vs. Evod

[cocacola31173]

Ok so I have been on a hunt for a smaller clearomizer that I can fit into my case on my Vision Spinners. I ordered a couple of evods but don;t like that you can hardly see the juice level. I noticed that the mini T3 has the same capacity and I have heard they taste just like a regular t3 which I am familiar with.

My questions is does anyone have a pic comparing the 2 side by side and i was thinking of trying some 50/50 mix and was wondering if the T3 can handle it ok?

Thanks!

 

[justinstar77]

MT3 on left EVOD on right. In my opinion they both work great with 50/50. If you do have wicking issues you can adjust the number of flavor wicks or the diameter of silica used. The juice window is about the same for both. I make my own coils and unless your getting the new "S" version of the MT3, as in MT3S the evod heads are far easier to rebuild...
Hope that helps.

 

[tatterz]

^Did you read anything he wrote?

Anyways, I've got some T3S parts/bases etc coming in the mail and I'm ordering some Mini T3s as well. If you get the Mini T3, deff make sure to get a T3S base for it as well as the T3S replacement heads. The standard T3 is being discontinued and replaced with the T3S

I've seen a pic of the two and they're practically the same size. And, personally, I prefer the taste of the T3 over the evod.

 

[Mad Scientist]

Mini T3, T3 and EVOD all work great for me with 20/80 thick juices.

I note though that it seems Kanger has been futzing with wicks (or maybe QC is just lacking) but I can say for sure that the T3 bases have more wick "room" than the EVODS. My guess is they caved to all the gurgling complaints and tightened up the space. I don't have any of the new design T3s to compare with but all my T3 will be rewicked until I'm in the ground and the old style bases are pryed from my cold dead hands lol. My suggestion if you rewick, get some original T3 tanks and bases before they're all gone.

 

[Garemlin]

The mini tastes nothing like the regular T3. Better flavor, slightly warmer vape and less airy draw. And none of the known problems of the regular T3 so far.

 

[cocacola31173]

I am sooo glad to see that! I like the looks of the evod but I like to easily see my juice level. At night its hard to see through that little window. I just wish they would put a smaller drip tip on the mini t3 but maybe later on they will.

 

[WorksForMe]

The mini tastes nothing like the regular T3. Better flavor, slightly warmer vape and less airy draw. And none of the known problems of the regular T3 so far.

I’ve read a lot of your posts here and on S.I.’s forum. IMHO. you should seriously consider trying an eGo passthrough battery and an Evod. Ego batteries open up a whole world of clearo options that you don’t have with X2s.

J.R.

I am sooo glad to see that! I like the looks of the evod but I like to easily see my juice level. At night its hard to see through that little window. I just wish they would put a smaller drip tip on the mini t3 but maybe later on they will.

I really hated the small windows on the Evod when I first got it. You have to hold it at the right angle to the light to see your juice. After a while, I got used to it, and now I like it. The mini T3s usually have the same issues as the original T3. You could use a new T3S coil with a mini T3 tank though.

J.R.

 

[Garemlin]

I’ve read a lot of your posts here and on S.I.’s forum. IMHO. you should seriously consider trying an eGo passthrough battery and an Evod. Ego batteries open up a whole world of clearo options that you don’t have with X2s.

J.R.

Thanks for the suggestion but I am done spending money on batteries for now. My next battery will be something like a Bolt or Provape. Something with interchangeable batteries but that does not cost a fortune like a Provari.

 

[OBDave]

I am sooo glad to see that! I like the looks of the evod but I like to easily see my juice level. At night its hard to see through that little window. I just wish they would put a smaller drip tip on the mini t3 but maybe later on they will.

I thought that would be a problem too, but I've gotten used to it and now the thing that bugs me is the condensation visible on the inside of the draw tube due to the clear mouthpiece.