My Auto Feed Sytem & Catch Cup for Provari

[pack21]

NUKE NUKE juice FEEDER CATCH CUP

I want to make coupler like GLV-3 in hardwood, for my Provari....for now i make the first steps.

3 VERSIONS


What you need;

VERSION Catch Cup, which you can update to Auto feed system



put this tip here, is seated in the connector.

put juice in catch cup ... with time to learn the right amount.

As you can see I've got juice there, which gives a good time to vaping.

you can put an o-ring on top, and then holes as you will see later .... so no leaks.

Version only Catch Cup

is made to fit over the edge off the cover

can lead or not an o-ring ... to better fit the cup .....

oring is pushed down with a cup smaller.

like this

TOTAL Juice Feeder


... Made of a load pen.... will be ideal a silicone tube.

get a wire to curved shape.

heating, shaping, refresh in cold water, heat ... etc. ....

like this

Open the lid of a bottle .... with a wire or screwdriver to boil.

Make a hole in the cup, to attach the tube feeder.

Attach the hose to the feeder and the catch cup

If you use the o-ring to seal the cup, you can make holes .... and more like a walk down ... if they want to lower the air, the oring fall into the first floor. (Not yet stuck downstairs)
Sand the top edges of the cup, to oring penetrate and cover the top.

Everything is now mounted;

And finally I have an Juice Feeder for 1 € .... in the next step will be to make a general type coupler like GLV-3 in hardwood.

Watch the oring and the holes may be more, or level ... ... more on top down under, then I can raise or lower the oring to have more or less hole pump.

The juice goes into the cup .... what flavor and steam.

Can you see the juice, to enter into the cup? where it's dark.

.... the next mod will make the coupler to the feeder like GLV3 for provari .

 

[misterD]

you have some real great ideas! very ingenious! thanks for sharing!

 

[pack21]

Well, I began studying the concept the juice feeder coupler for provari ...... The prototype will be on solid hardwood and possibly later milling in a aluminum block.

Also wiil try to make the catch the cup in a drip shield empire, i must order one.

 

[PKZap27]

--snipped--

Could you please post the "My Juice Feeder Sytem & Catch Cup for Provari" in the Modder's section of the ECF?

Modders Forum

 

[pack21]

Could you please post the "My Juice Feeder Sytem & Catch Cup for Provari" in the Modder's section of the ECF?

Modders Forum

ok, no problem.

I didn't know I could not put here, is there any problem?

 

[PKZap27]

ok, no problem.

I didn't know I could not put here, is here any problem?

I don't see a problem with posting it here. However, I felt that posting it in the Modder's section will get you more feedback and comments about your Mod.

Members in the Modder's section may even possibly decide to machine parts for your design...

The possibilities are endless.

Here is a link to your post in the Modder's section of the ECF.

http://www.e-cigarette-forum.com/fo...eder-sytem-catch-cup-provari.html#post3611290



Edit to add;

BTW, nice job on this MOD for the ProVari.

 

[misterD]

i dont think he meant that you shouldn't post it here. you should ALSO post it in the modders subforum is what he meant!
i really liked what you did here and what you did with the reo-mini! post that one too on the modders forum!!

 

[pack21]

ok, i have put threre the mod.


Thanks buddy.