My on the road coil kit
- Thread starter Outcast
- Start date
- th_trl_thread_readers 0
- Status
for day to day I don't take anything, just my mod.. on trips then tis was a few months ago
2 screw drivers
2 allen keys
1 multitool
24 and 28 g kanthal
nail clipper
4 spare 18490
2 spare 18350
extra 18490 mod
extra top cap for the 4nine
2 rdas
2 driptips
spare magnets for the 4nine
2 feet of rayon
65ml of my juice
the only thing that doesn't fit is the charger
2 screw drivers
2 allen keys
1 multitool
24 and 28 g kanthal
nail clipper
4 spare 18490
2 spare 18350
extra 18490 mod
extra top cap for the 4nine
2 rdas
2 driptips
spare magnets for the 4nine
2 feet of rayon
65ml of my juice
the only thing that doesn't fit is the charger
for day to day I don't take anything, just my mod.. on trips then tis was a few months ago
2 screw drivers
2 allen keys
1 multitool
24 and 28 g kanthal
nail clipper
4 spare 18490
2 spare 18350
extra 18490 mod
extra top cap for the 4nine
2 rdas
2 driptips
spare magnets for the 4nine
2 feet of rayon
65ml of my juice
the only thing that doesn't fit is the charger
Whoa man that is vapocalypse care package. Looks like you're ready for war
This has been going with me - everything I need, and haven't really NEEDED it yet...
Knock on my woodville (which stays home).
Edit - oh, and this is for anything from overnight in a hotel to a week in a tent...not a daily carry-to-work, lol. Daily, I just leave with a fresh battery and a full bottle in a Reo.
Knock on my woodville (which stays home).
Edit - oh, and this is for anything from overnight in a hotel to a week in a tent...not a daily carry-to-work, lol. Daily, I just leave with a fresh battery and a full bottle in a Reo.
Are those insulators for Protanks and such? If so where did you get them and do they fit well?Way too much lol
Sent from my A0001 using Tapatalk
Thanks for the reply.
Nice kit btw.
Those are for the kanger occ type.
They work great actually like them better than the factory ones. I'd rather silicone then rubber. They are from eBay.
Sent from my A0001 using Tapatalk
Thanks, was needing some silicone ones for a Kanger protank single coil head. According to friends the ones they got were a bit too large for the regular Kanger BCC cils.
I enlarged the wick slots on my coil heads to 2mm and put a cotton wicked 30 ga 2mm 1.6 ohm coil in mine. I also bored out the center pin and top stem on mine.
How do you like the OCC heads?
I used them for a while now and love them. Easy to recoil and wick. .7 coil now with 25 watts and smooth thick vapor. I have a sub tank nano.
Sent from my A0001 using Tapatalk
The nano has been far less finiky then the protank coils. I'd go for it.
Sent from my A0001 using Tapatalk
My Vapemergency kit and Daily Vape Case.
Vapemergency Kit:
Kanthal in 32 (protank rebuild), 30, 28 and 26 gauge.
Nickel in 28 and 26
Vapertowel
Panzer mod with RDA
1.8 Ohm prebuilt Nickel, Kanthal, Nickel wires (for protank)
Silica wick (for protank)
Small wire spool made from a blank ID card
Rayon wick material (for everything not the protanks)
Multimeter
Custom 510 to multimeter adapter
Battery wraps
Forceps
Straight point tweezers
Scissors
Q-tips
Bent point tweezers
Juice tasting RDA (Castle built with no wick)
Various juices
Butane for torch
Coil wrapping mandrel
Screwdriver (green one)
Screwdriver (silver one)
Butane torch
Various size screws for wrapping spaced coils
Needle nose pliers (yes I know they are pink)
Flush cutters
510 male / male adapter (to test voltage of mods)
Daily Vape Case:
ADV Juice
Spare pre-built RBA coils
Spare Sony VTC4 18650 Batteries (one re-wrapped)
Phillips screwdriver (to make sure the posts of the rba's are tight before installation)
Joytech Evic Mini with Zephyrus tank and an RBA coil.
Sorry for the lousy lighting and pic quality. Its hard trying to get good images down to one Mb.
Last edited:
- Status
