trying a test set up for a small li po and having problems.when connecting ...it just blinks 3 times at me..and then stops. unsoldered the pos to check for shorts but all ok..it is the 4 botton board from mad vapes.what could be the problem ?rolf
-
Need help from former MFS (MyFreedomSmokes) customers
Has any found a supplier or company that has tobacco e-juice like or very similar to MFS Turbosmog, Tall Paul, or Red Luck?
View thread
- Status
how about a picture showing your build....might help us to be able to help you...
hard to see....but...
is the li-po a single cell (kinda looks like a multi-cell pack)? battery voltage? fully charged? did the board come with any diagrams/spec sheet?
did you change the fire button?
alot more info needed to help ya out.....a diagram would be most helpful...did the board come with operating instructions (button presses, error messages (flashes), etc.
is the li-po a single cell (kinda looks like a multi-cell pack)? battery voltage? fully charged? did the board come with any diagrams/spec sheet?
did you change the fire button?
alot more info needed to help ya out.....a diagram would be most helpful...did the board come with operating instructions (button presses, error messages (flashes), etc.
in looking at the picture on madvapes web site:
I see one red wire......I assume this is the power in (+)
I see 2 black wires....connected to the same solder point on the board...I assume this is the (-) connection from the battery and the negative connection to the atty connector...
I see two small black wires coming from the board connected to a off-board tactile switch.....
What I do not see is a wire coming from the board that should connect to the atty (+) center pin.....
Are my assumptions correct as to what I see on madavpes site?
EDIT: from your poor picture it almost looks like you have soldered a white wire on the board to go to the atty (+) pin....but the picture is not clear enough for me to tell for sure...sorry...
I see one red wire......I assume this is the power in (+)
I see 2 black wires....connected to the same solder point on the board...I assume this is the (-) connection from the battery and the negative connection to the atty connector...
I see two small black wires coming from the board connected to a off-board tactile switch.....
What I do not see is a wire coming from the board that should connect to the atty (+) center pin.....
Are my assumptions correct as to what I see on madavpes site?
EDIT: from your poor picture it almost looks like you have soldered a white wire on the board to go to the atty (+) pin....but the picture is not clear enough for me to tell for sure...sorry...
Last edited:
tnx the comeback.
the cell is halv a 7.4 lipo I did not do any additional charging but it seems to be plenty charged I ll try to top it up.
so this cell is 3.7 or so .the board has no instructions ...has two longer wires blk and red which go to the battery used a pt fuse in pos.
the short wires go to the 510 conector blk =negative ..white =+
the fire botton is the same as supplyd I just made a fiberglas small cover to glue on and hold the switch in place ...did not want to glue the switch it selv in case I want to reuse it. on the fire botton I had to resolder one lead which came loose from handling .
I connect the negative leads to complete the circuit then it flashes three times and that it....unsoldered atty +same thing ..pressing fire botton or not is also no difference
instructions and error messages would may be helpful but madvapes don't supply any
tnx the help ...rolf
the cell is halv a 7.4 lipo I did not do any additional charging but it seems to be plenty charged I ll try to top it up.
so this cell is 3.7 or so .the board has no instructions ...has two longer wires blk and red which go to the battery used a pt fuse in pos.
the short wires go to the 510 conector blk =negative ..white =+
the fire botton is the same as supplyd I just made a fiberglas small cover to glue on and hold the switch in place ...did not want to glue the switch it selv in case I want to reuse it. on the fire botton I had to resolder one lead which came loose from handling .
I connect the negative leads to complete the circuit then it flashes three times and that it....unsoldered atty +same thing ..pressing fire botton or not is also no difference
instructions and error messages would may be helpful but madvapes don't supply any
tnx the help ...rolf
so when you have the battery +, battery -, and switch connected only....you get the 3 flashes even when you do not press the switch?
I'm wondering if 3 flashes means a shorted atty?.... could the atty black wire and atty white wire solder points (at the board) be touching? just a guess...
also ya might unhook one wire from the switch to see if that clears the flashing....tactile switches can short from the heat of soldering.....
DISREGUARD>>>> see posts below.....
I'm wondering if 3 flashes means a shorted atty?.... could the atty black wire and atty white wire solder points (at the board) be touching? just a guess...
also ya might unhook one wire from the switch to see if that clears the flashing....tactile switches can short from the heat of soldering.....
DISREGUARD>>>> see posts below.....
Last edited:
If that is a ceramic cap on that red line then seems wrong? they would not nomally sit in line but parallel across lines?
I'm assuming that is an in-line fuse....
found this for ya...may help,,,
VV Gripper Tips:
•Insert the battery + end first, the screen will blink 3 times to indicate that a connection has been made.
•Click button # 3(the button below the '- and +' buttons) very quickly 5 times to turn the unit on of off.
•Hit + or - to adjust the voltage.
•When the unit is on, click button # 3 (the button below the '- and +' buttons) once to show the ohms and voltage.
Moral of story.....instructions from Madvapes would have saved ya some grief......LOL
here is a video.....
http://www.youtube.com/watch?v=G5d81Xz9BN4&feature=player_embedded#at=47
found this for ya...may help,,,
VV Gripper Tips:
•Insert the battery + end first, the screen will blink 3 times to indicate that a connection has been made.
•Click button # 3(the button below the '- and +' buttons) very quickly 5 times to turn the unit on of off.
•Hit + or - to adjust the voltage.
•When the unit is on, click button # 3 (the button below the '- and +' buttons) once to show the ohms and voltage.
Moral of story.....instructions from Madvapes would have saved ya some grief......LOL
here is a video.....
http://www.youtube.com/watch?v=G5d81Xz9BN4&feature=player_embedded#at=47
Last edited:
to jucemoose.....no that's not a capacitor it is an inline pt fuse.
to retird...well I think you solved the problem !! I will print out the instructions looks like that is the problem digital challencedold kraut on this end!i will also test to make sure the switch is ok
thanks all the help rolf
retired !just to let you know....the thing works perfect !! now I can test how long that 900 ma will vape
to retird...well I think you solved the problem !! I will print out the instructions looks like that is the problem digital challencedold kraut on this end!i will also test to make sure the switch is ok
thanks all the help rolf
retired !just to let you know....the thing works perfect !! now I can test how long that 900 ma will vape
Last edited:
Your welcome my friend....just waiting for your post that it is working just fine.........
THX for editing your last post that it is working.....enjoy.....
THX for editing your last post that it is working.....enjoy.....
Last edited:
- Status
