If it does, AND they change the build material from brass to stainless steel or aluminum...then they will get my $$$. The looks/functionality is great, but they really missed the mark with weight and no batt life meter.
New iTaste VTR (not released)
- Thread starter bikerbeagle
- Start date
- th_trl_thread_readers 0
- Status
If it does, AND they change the build material from brass to stainless steel or aluminum...then they will get my $$$. The looks/functionality is great, but they really missed the mark with weight and no batt life meter.
Will the original iClear 30 clearo fit in on the side of it without the adapter, or is it too big?
MVP V1 only has green-yellow-red. No digital battery indicator.
MVP V2 has voltage status (press P and U buttons and it will show you Resistance and battery voltage). I don't know if that is also the case for V1. But it's not like Innokin is unaware of the usefulness of that reading.
Also, I forgot to ask... Does the VTR take flat tops, button tops, or does it matter (batteries)?
I'm using FLAT tops and they work.
Also for carto tank lovers I picked up a Smoketech Pyrex DCT[FONT=arial, sans-serif]ank. It took about a half hour of filing with a round steel file but I crammed it in.
6mls of carto goodness
[/FONT]
Last edited:
Yep I had a little bit of leakage and stuck a tissue in but worry about it getting under the wheel. I don't see any way to remove it.
As far as I know it is solid brass so you are not really exposing anything - not sure what you mean. For this tank, it was probably less than a mm taken off. You could take off as much as yo want but you are weakening the ring so obviously it may crack at some point
It's chromed on top of brass, isn't it?
I assumed mgmrick meant doesn't the yellow show through if you file it wider? (Which was my concern too)
I assumed mgmrick meant doesn't the yellow show through if you file it wider? (Which was my concern too)
I think the ring might be stainless steel - I didn't see any color change. I did scratch the inner part of the grooved tank area while I was filing and I do think you can see some yellow coming thru. The inside of the ring just looks scratched up, but you can't see either of these areas with the tank in.
For me - I am much more concerned about the utlility than the look, but it looks great with the tank in.
Last edited:
Yes, now I've got mine it's clear - the top, including the ring around the top of the atty, and bottom (and also the surround for the button) are stainless steel and the body between them is brass.
It's brass, I took rough sandpaper to all three sections and removed the plating, it is brass.
Sent from my GT-N7000 using Tapatalk 4
Sent from my GT-N7000 using Tapatalk 4
I just got mine today and am waiting for my batteries to charge, but the instructions do say that if your press and hold the select button to get the Ohm reading, and then press and release the select button again, it will show the voltage of the battery.
Have you got a photo? Mine has a deep scratch inside the ring, and the peak of the battery cap has been ground back, and I have to say - it looks like stainless steel to me.
Looks much like the MVP end fittings... with one interesting difference: no CE mark
As I said in my review, individual parts may be constructed of other material but the main 3 sections are brass.
Sent from my GT-N7000 using Tapatalk 4
Sent from my GT-N7000 using Tapatalk 4
While I don't know what the manual says, it is very clear from several video reviews that pressing the button does indeed show you the Ohms, but then switches to the mode settings. Depending on which mode you're in, you will see the voltage or power SETTING. Nowhere has anyone shown that you can get the battery voltage READING. That's a very important difference. You can only see the voltage you are setting, but not the actual battery voltage.
- Status
Similar threads
