New KangerTech SUBTANK
- Thread starter Vap0rnomics
- Start date
- th_trl_thread_readers 0
- Status
In your opinion, will the Subtank with the 1.2 coil give good flavor at 17-20W? I'm wondering if this will be ok with an MVP20 as I don't care about clouds but want to move away from Nautilus due to wicking material concerns. Thanks!
Should be just fine! i have run mine at 17 watts and the flavor is there. Also loving the RBA deck as you can build a coil to you own specs and you have access to the deck without emptying the tank which is a huge plus!
Also the chimney is slightly smaller on the RBA section giving a little more restricted airflow but more intense flavor IMO
Also the chimney is slightly smaller on the RBA section giving a little more restricted airflow but more intense flavor IMO
Yes it will the only thing that I have done when I go higher watts is use a different drip tip. Clouds will be from more vg less pg.
https://www.youtube.com/watch?v=WMUOtwsd7_E
This is also a great vid on how to rewick the Stock coils without rebuilding. Little trick to getting the amount of cotton just right but hell it works like a dream!
This is also a great vid on how to rewick the Stock coils without rebuilding. Little trick to getting the amount of cotton just right but hell it works like a dream!
It would be perfect IMO. I'm using a 1.1 build on the RBA and at 17.5 on the IPV mini. Think I like the build in this tank better than my dual 0.8 in the billow. If you're not wanting hot / warm vapor then 17-20 is a really good spot for 1.1-1.2.
It also pushes down the pin on your device. The MVP 2 isn't springloaded and wasn't working on my Kayfun after using it with the subtank. I had to pry the pin out a bit and then it detected the Kayfun again. I have decided to only use the subtank with my Magneto where I can adjust the pin to fit just right.
I'll test it with the MVP 3 when it is released.
Can someone please provide a picture of the old BDC coils in the Subtank (with the tank closed)?
There's a video https://www.youtube.com/watch?v=H3rfKegWwiE saying they'll fit, but you can't see anything.
There's a video https://www.youtube.com/watch?v=H3rfKegWwiE saying they'll fit, but you can't see anything.
I tried it this morning and it worked flawlessly. Just have to be patient when twisting the cotton out but it works great and I save myself definitely one coil maybe two or three. Great tip and so much easier than taking the whole coil apart. [emoji106]
Will the occ coils from the subtank fit in the coming mini subtank? No one has talked about this.
Yes. occ coils are compatible with all three. according to Kanger
PBusardo gave us a bit of a sneak peak at the Mini and Nano in action in his latest video reviewing the Cloupor Mini, the nano was the topper he used for much of the mod testing.
hey Croak... been thinking about your issue with the glass being able to turn easily and leaking at the base connection. Those two things are related... duh....you knew that. 
I can turn my glass as well, not easily but it turns while it's installed. It leaked at the base connection when I first got it...just seeped slightly but enough to be annoying.
That bottom gasket on the base isn't correct on yours. If it's not exactly seated in the right spot, it will seep at the base during use.... on mine. I know you said you messed with it trying to fix but it has to be that gasket seating incorrectly on the base (with the coil) still. I see your reason for the bad review, I'd be ...... off too.
That gasket has stayed put in the groove on the base for the last few times I've had mine apart....even during cleaning under running water. No leaks now, I can still turn the glass a little no matter how tight I screw the base on. Dunno.... trying to be helpful as it's a drag putting out that amount of money for a leaker.
I can turn my glass as well, not easily but it turns while it's installed. It leaked at the base connection when I first got it...just seeped slightly but enough to be annoying.That bottom gasket on the base isn't correct on yours. If it's not exactly seated in the right spot, it will seep at the base during use.... on mine. I know you said you messed with it trying to fix but it has to be that gasket seating incorrectly on the base (with the coil) still. I see your reason for the bad review, I'd be ...... off too.
That gasket has stayed put in the groove on the base for the last few times I've had mine apart....even during cleaning under running water. No leaks now, I can still turn the glass a little no matter how tight I screw the base on. Dunno.... trying to be helpful as it's a drag putting out that amount of money for a leaker.
Has the original 25mm Subtanks been recalled? I was browsing on Kangers website and noticed its no longer offered for sale, just the Subtank Mini and Nano?
I purchased the 25mm Subtank but haven't opened mine yet as I have no box, but if theres a recall or such, I'll leave it un-opened and return to my local store. Anyone know?
I purchased the 25mm Subtank but haven't opened mine yet as I have no box, but if theres a recall or such, I'll leave it un-opened and return to my local store. Anyone know?
VapinGreek has them reviewed already: https://www.youtube.com/watch?v=GzTDbG6v4Fo
- Status
Similar threads
- Locked
- Locked
