-
Need help from former MFS (MyFreedomSmokes) customers
Has any found a supplier or company that has tobacco e-juice like or very similar to MFS Turbosmog, Tall Paul, or Red Luck?
View thread
NEW YIHI SX MINI ML CLASS!
- Thread starter smokyribs
- Start date
- th_trl_thread_readers 0
- Status
How open is the airflow bud? Looking for a single coil rta with a nice open draw, decided it's time I get back in to making my own coils again with all the regs closing in on us!
Cheers bud, just seen the serpent is on fasttech, missed the 20% off but think it's still 15%.
Is the serpent easy to build on, last time I built a coil was on the squape reloaded lol
Its kind of goofy, but I still find it easy, so I would say yes. The post holes are offset, so you mount the coil diagonal naturally. I just insert one leg all the way in against one post, clip the other leg at the post hole, then move the short leg into the post hole, tighten down, and clip the other leg.
Thanks bud, just bagged oneIts kind of goofy, but I still find it easy, so I would say yes. The post holes are offset, so you mount the coil diagonal naturally. I just insert one leg all the way in against one post, clip the other leg at the post hole, then move the short leg into the post hole, tighten down, and clip the other leg.
Yep. Hey did your SX stop working when Chinese New Year started? The website went down.
Can you shut air flow down to do a mouth to lung? I'm reverting back to the good old days only in temp control mode.Its kind of goofy, but I still find it easy, so I would say yes. The post holes are offset, so you mount the coil diagonal naturally. I just insert one leg all the way in against one post, clip the other leg at the post hole, then move the short leg into the post hole, tighten down, and clip the other leg.
Sent from my iPhone
You can, it has adjustable AFC ring, but I don't think that is really what its intended for. With the AFC closed down tight for mtl, still have that wide bore center airflow. I would say there are better single coil rtas out there for mtl.
You could modify the serpent slightly by using some type of tube to drop in the center pin airflow to cut down the diameter, which would make it more suitable for mtl. A couple people in the serpent thread have done so to make it more suitable for mtl.
Although the Yihi site is not doing too well, I was able to get the following:
YiHiSX350J-V2-V2206-20160126-English.SXI
I didn't see it posted anywhere on their site, but this link does appear to be v206 for the non-SXM or for the modders chips.
YiHiSX350J-V2-V2206-20160126-English.SXI
I didn't see it posted anywhere on their site, but this link does appear to be v206 for the non-SXM or for the modders chips.
But now I did get the SXML version of v206
SXmini_ML_Class_V2206-20160126-English.SXI
And it does work and reports v2.206 when powered on with the battery inserted.
Not sure what has been upgraded or changed since I have no documentation on this version.
SXmini_ML_Class_V2206-20160126-English.SXI
And it does work and reports v2.206 when powered on with the battery inserted.
Not sure what has been upgraded or changed since I have no documentation on this version.
How many RTA / RDA have you accumulated? lol
Let us know if you notice any differences. Been unable to get to the yihisxmini.com site but notice this update is about 7KB smaller than the previous releases. Was it released by Yihi for the ML or from someone else?
I bought myself a few gifts for Valentines. lol I got the Bachelor, a Griffin with a few colored glass tanks, and an Avocado from Fastech along with a few ceramic drip tips while they had a 20% off sale. I know it will be a few weeks before I see them due to the holiday and shipping times.
Those firmwares were just posted on the FB page for the SXM Brotherhood. I am using it but don't notice any changes with the settings I am using. There will probably be something mentioned soon but I didn't see anything on the official Yihi pages after lots of retries with their almost crashed but still limping along website.
I updated to version 2.206 yesterday and all seems to be working well.
The version of the firmware I installed came directly from YiHi for the chip board SX350J-V2 and not from the ml class section they have. They released the 206 firmware for their distributed chip boards first for some reason.
The version of the firmware I installed came directly from YiHi for the chip board SX350J-V2 and not from the ml class section they have. They released the 206 firmware for their distributed chip boards first for some reason.
I see the link has been pulled. YIHI's site is loading now and v2.206 isn't listed.
Check on YiHi e cigar dot com
They release software for people who buy only the boards, not the entire ML class.
People and manufacturers who bought the V2 board are receiving the 206 software before people who have bought the ML class unit.
Q:I just upgraded my device to V2.203, found there is V2.206 for boardSX350J-V2, any different between V2.203 and V2.206 ?
A: SX Pure function inside V2.206 support the Atomizer-with SX Puretechnology-from IPV company. If you have their new atomizer, you need upgradeto V2.206. or no need upgrade one more time.
SXmini-SXmini maker,SXmini,yihisxmini,yihiecigar,sx350,yihi sx350, yihi sx350 mini, yihiecigar sx350 mini, gravity sensor,www.yihisxmini.com,120w device
A: SX Pure function inside V2.206 support the Atomizer-with SX Puretechnology-from IPV company. If you have their new atomizer, you need upgradeto V2.206. or no need upgrade one more time.
SXmini-SXmini maker,SXmini,yihisxmini,yihiecigar,sx350,yihi sx350, yihi sx350 mini, yihiecigar sx350 mini, gravity sensor,www.yihisxmini.com,120w device
- Status
Similar threads
- Locked
