RDA Nipple RDA by TJT

[sonicbomb]

Cons - The AFC adjustment would be a pain until you had it setup how you liked it, and I think you would struggle to drip through that tip. Expensive at around 140 buckeroos.

Pros - Looks like a nipple (ooorr missus!)

- Stainless Steel Cap and drip tip
- 22 mm in diameter,
- 24 mm height with a dedicated drip tip
- 20 mm height without drip tip
- Brass center post
- Single coil, dual coils
- Brass nozzles for air flow control (1mm, 1.5mm, 3mm, blind for single coils)
- Storage place for nozzles in deck
- Extra small chamber

 

[VaporDaze]

I wanna suck on that nipple!

 

[aggo]

Yikes, that'd be a pretty hot nipple to suck on.

 

[ElevenEleven]

I reeeaally like the storage for the airflow nozzles.

 

[greasegizzard]

My OCD sense is tingling seeing those airflow screws not being horizontal or vertical... Other than that, looks pretty nifty.

 

[jjatl]

A nipple clone just popped up on FT.

https://m.fasttech.com/products/0/10020663/4428800-nipple-styled-rda-rebuildable-dripping-atomizer

 

[kformeck]

Loving my nipple! Very easy to build, fantastic flavor and it doesn't seem to get as hot as you might expect.

@Isabella Liu I would imagine this RDA will as hot as some of the other high end atties like the NarDA and Snapdragon.

 

[sofarsogood]

Loving my nipple! Very easy to build, fantastic flavor and it doesn't seem to get as hot as you might expect.

@Isabella Liu I would imagine this RDA will as hot as some of the other high end atties like the NarDA and Snapdragon.

I got stuck on an SV clone. It's become the only atomizer I use because smaller size, air supply good for MTL and minimizing leaks and best flavor of anything I've got. If I gete a Nipple I'll make a plug for one side. I'm guessing the screw size is 4 mm. Do you have an SV style for comparison by any chance?

 

[kformeck]

I got stuck on an SV clone. It's become the only atomizer I use because smaller size, air supply good for MTL and minimizing leaks and best flavor of anything I've got. If I gete a Nipple I'll make a plug for one side. I'm guessing the screw size is 4 mm. Do you have an SV style for comparison by any chance?

I don't have anything from SOV so I can't compare but I'm pretty sure the outer diameter of the airflow screws on the nipple are 3mm; I have no idea what the threading is though.

 

[sofarsogood]

I don't have anything from SOV so I can't compare but I'm pretty sure the outer diameter of the airflow screws on the nipple are 3mm; I have no idea what the threading is though.

Once I know the screw size may be I can make a plug for one side and customize the air for the other side. I have an unfair advantage. I work in a custom build shop (automotive assembly lines and machines). Among my personal tools are a fractional drill bit set, production vise, 15" drill press and even a hobby size lathe. Now that I've seen this solution may be it's a way to close the second air supply on some of my other rda's.

 

[jjatl]

I got stuck on an SV clone. It's become the only atomizer I use because smaller size, air supply good for MTL and minimizing leaks and best flavor of anything I've got. If I gete a Nipple I'll make a plug for one side. I'm guessing the screw size is 4 mm. Do you have an SV style for comparison by any chance?

It sounds like we have similar tastes in RDAs. I just recently purchased a snapdragon clone from FT, and it is fantastic. I build it for single coil and put its flavor up there with my derringer. It is not small, but I thoroughly enjoy it. It has a larger well than the derringer and doesn't get messy with condensation.

 

[sofarsogood]

It sounds like we have similar tastes in RDAs. I just recently purchased a snapdragon clone from FT, and it is fantastic. I build it for single coil and put its flavor up there with my derringer. It is not small, but I thoroughly enjoy it. It has a larger well than the derringer and doesn't get messy with condensation.

I have a derringer clone and stopped using it because I prefer the SV flavor and the SV has only one air supply on one side so controling leaking is simpler. I like a small form factor over all but don't want to give up anything. The Nipple is shorter, I pulled the trigger on the iStick Pico. That combination could be a form factor roughly comparable to the egrip which I don't use any more because of the SV and better endurance from an HG2. I'll take a look at the snapdragon

 

[sofarsogood]

It sounds like we have similar tastes in RDAs. I just recently purchased a snapdragon clone from FT, and it is fantastic. I build it for single coil and put its flavor up there with my derringer. It is not small, but I thoroughly enjoy it. It has a larger well than the derringer and doesn't get messy with condensation.

A Nipple clone was delivered today from FT. From the bottom of the deck to the top of the drip tip it's the same height as my derringer clone. I'd say the flavor is not better than my SV clone but close enough. I love the low profile. I've got a Pico on the way. The Nipple and Pico should be a very compact pair.

The Nipple juice well is small and shallow to allow for threaded holes in the bottom for the spare air screws. I'd rather have a bigger juice well. I like the super short drip tip. They are available separately so I'm getting some.