O-ring List for Some of the More Popular Atties

[dwcraig1]

This is a work in progress and I would like folks to add to the list. In the end if complete enough a "Sticky" may be born.
All sizes listed by me are I.D. then cross section.
All are Nitrile/ Buna unless otherwise noted.
Accuracy is most important so make sure of your source. I made the mistake of coping and pasting from another forum with wrong info recently.
Your help will be greatly appreciated.

 

[dwcraig1]

O-ring sizes for Kafun 3.1, Lite, Lite Plus, V2
Chimney top: 5 mm x 1.5 mm
tank sections: 18 mm x 1 mm
Fill screw (if applicable) 2 mm x 1 mm

 

[dwcraig1]

O-ring sizes for kayfun 2.1 mini
Chimney top: 5 mm x 1.5
tank Sections: 10 mm x1 mm

 

[dwcraig1]

O-ring sizes for Taifun GT
17 x 1.5 are at each place where the end of the tank seals..
12 x 1 mm on the chamber cap.
11 x 1 mm or 12 x 1 mm under the sliding sleeve.
4 x 1 on the end of the chimney (fill line).
2 x 1 mm under the 510 screw's head.
5 x 1.5 mm goes on the drip tip

Note: 11 x 1 mm on most, 12 x 1 mm on some (under sliding sleeve)

 

[dwcraig1]

Oring sizes for Taifun GS (mini)
Top Cap/Tank Top + Tank Bottom: 12 mm x 1 mm
Chimney Tube: 4 mm x 1 mm
Base Top: 12 mm x 1 mm
Chamber Cap 8 mm x 1 mm
510 screw 2 mm x 1 mm
Drip Tip 5 mm x 1.5 mm

 

[dwcraig1]

O-ring sizes for Rose v2
Chimney: 7 mm x 1 mm
Coil body top: 15 mm x 1 mm
Coil body bottom: 18 mm x 1 mm
Tank sections: 18 mm x 1 mm
Air control ring: 18 mm x 1 mm
Brass 510 screw: 2 mm x 1 mm

 

[Bill's Magic Vapor]

What a great thread D!

If I knew the oring sizes of anything other than my Taifun GT's, I would certainly share it here!

Great job here! I hope others find this thread and participate! Good luck!

 

[dwcraig1]

O-ring sizes for RJ Mods MISTer Silica Hydrid v2 and v3 tank atomizer.
Tank top (outer) and tank/base: 18 mm x 1 mm
Tank top (inner): 7.5 mm x 1.5 mm

 

[dwcraig1]

O-ring sizes for Fogger 4.0 ( maybe more of the v4's)
Inside top cap (top of glass tank): 17 mm x 2 mm (softer than duro 70 but duro 70's should still work).
Base (bottom of tank): 17 x 2 mm (this one's real soft also)
Top of chimney: 3 mm x 1 mm
Bottom of chimney: 10 mm x 1
Fill screw: 2 mm x 1

 

[txtard]

This needs to be a sticky for sure!

 

[elenamylove]

If I get some time later perhaps I can consolidate and organize it better for everyone. This is something I been wanting info on for weeks.

 

[kickflipsnnollies]

Info on screw sizes/threading would be cool too.

 

[kathi17]

Info on screw sizes/threading would be cool too.

I agree.

I keep trying to find some o ring sizes so I can contribute, but all I can find are the Kayfun ones and the Taifun ones, and those are already here.

 

[bsoplinger]

Somebody's already got a pretty good list of screw sizes, he refers to it in his .sig file but don't remember his nick. I can find most sizes but where can I get decent silicone in the tiny fill screw 2x1mm size?

Sent from my Kindle Fire HDX using Xparent Purple Tapatalk 2

 

[dwcraig1]

Somebody's already got a pretty good list of screw sizes, he refers to it in his .sig file but don't remember his nick. I can find most sizes but where can I get decent silicone in the tiny fill screw 2x1mm size?

Sent from my Kindle Fire HDX using Xparent Purple Tapatalk 2

Silicone Oring 2 x 1mm Price for 25 pcs - Orings and More
These are dura 75 not them soft ones coming on clones.

 

[dw117]

Great idea this.

Been looking for confirmation that the o-ring for the barrel of the Quasar (the one that "reverse fits") is 17mm ID x 1mm. I'm pretty sure it is.

 

[dwcraig1]

O-ring sizes for Aqua
Top cap: 17 mm x 1 mm
Chimney: 7 mm x 2 mm
Base to tank: 13 mm x 2 mm
Inside base on big insulator: 13 mm x 2 mm
On positive pin inside large insulator: 2 mm x 1 mm (3)