Picture of Your Setup Part 2!

Status
Not open for further replies.

IonMan

Senior Member
ECF Veteran
Verified Member
Aug 8, 2014
299
583
Bradley, Illinois, United States
166008279f3dafde8e19fb2f08fe0cec.jpg
 

KTMRider

Vaping Master
ECF Veteran
Verified Member
Jul 5, 2014
4,538
18,079
NJ
Nice and simple, I like it.

Can't wait till my Lemo 2 comes in. How do you like it? And what kind of builds do you run in it?
Thanks, the rDNA40 is still my favorite device.

I just got the Lemo 2 yesterday. I tried it with the pre-built .5Ω coil and while it was pretty cool blowing thick clouds with an atomizer, it burned thru the tank in a few hrs. I have a .12Ω Ni200 (7 wraps, 28g, 3mm ID) and it's working well with rayon. The drip tip is ridiculous so I replaced it with a KF v4 drip tip.
 

VCross

Senior Member
ECF Veteran
Verified Member
Jun 6, 2015
213
239
38
Yucaipa, California
Folgers with Grape, Coconut Cream Pi (3.14159mg), Blueberry Cream & Strawberry Cream probably all taste better than sweaty guitar strings [HASHTAG]#justsaying[/HASHTAG]

10482478_1667594463471377_2790537872050438774_o.jpg
I don't know why but it's driving me insane that you don't have the black Subtank on the black SUBOX. [emoji35]
 

silvertorch

Senior Member
ECF Veteran
Feb 4, 2014
116
149
Chicago
Thanks, the rDNA40 is still my favorite device.

I just got the Lemo 2 yesterday. I tried it with the pre-built .5Ω coil and while it was pretty cool blowing thick clouds with an atomizer, it burned thru the tank in a few hrs. I have a .12Ω Ni200 (7 wraps, 28g, 3mm ID) and it's working well with rayon. The drip tip is ridiculous so I replaced it with a KF v4 drip tip.

I may have to finally get some Ni200 and start building with it. Any issues with Temp Control and the Lemo 2? I heard that the KF4 had issues?
Right now I run a Lemo on my rDNA40 with a 0.75 ohm build, doesn't use up juice that badly.
 

KTMRider

Vaping Master
ECF Veteran
Verified Member
Jul 5, 2014
4,538
18,079
NJ
I may have to finally get some Ni200 and start building with it. Any issues with Temp Control and the Lemo 2? I heard that the KF4 had issues?
Right now I run a Lemo on my rDNA40 with a 0.75 ohm build, doesn't use up juice that badly.
No issues with the Lemo 2 but it's only been a day. There are easy fixes for the KF v4. I tried a few and the best is to just bend the spring end in a bit so it connects the 510 with the center post a bit better. Solid, repeatable readings after that simple mod.

.5Ω at 25w was gulping juice. I tried at 30w and 35w. I don't know how people vape that high with a .5Ω coil.

I highly recommend ni200 (28g). I haven't tried titanium and don't have any plans to since ni200 is working really well for me. Absolutely love my rDNA40. I only wish it was a large screen. I'm tempted to pick another one up still.
 

silvertorch

Senior Member
ECF Veteran
Feb 4, 2014
116
149
Chicago
No issues with the Lemo 2 but it's only been a day. There are easy fixes for the KF v4. I tried a few and the best is to just bend the spring end in a bit so it connects the 510 with the center post a bit better. Solid, repeatable readings after that simple mod.

.5Ω at 25w was gulping juice. I tried at 30w and 35w. I don't know how people vape that high with a .5Ω coil.

I highly recommend ni200 (28g). I haven't tried titanium and don't have any plans to since ni200 is working really well for me. Absolutely love my rDNA40. I only wish it was a large screen. I'm tempted to pick another one up still.

Thanks for the advice.

I had to send my rDNA40 back, had issues with charging and a few others. It was sent back with the large screen and new version of the "firmware".
 
Status
Not open for further replies.

Users who are viewing this thread