Log in
Register
Welcome to the world's largest e-cigarette website.
The voice of vaping since 2007
Search
Search titles only
By:
Search titles only
By:
Welcome to the world's largest e-cigarette website.
The voice of vaping since 2007
Forums
Forum list
New posts
Search forums
Leaderboards
Products
Search reviews
Brands-Connect
Latest content
Vaping.com
Disposable Vapes
Vape Juice
Vape Kits
Vape Pods
Vape Coils
Star Suppliers
Media
New media
Search media
Blogs
New entries
New comments
Blog list
Search blogs
Log in
Register
Search
Search titles only
By:
Search titles only
By:
More options
Toggle width
Share this page
Share this page
Share
Facebook
X (Twitter)
Reddit
Pinterest
Tumblr
WhatsApp
Email
Share
Link
Menu
Install the app
Install
Forums
E-Cigarette Community
New Members: Introduce Yourself!
Picture of Your Setup Part 3!
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Fozzy71" data-source="post: 18239557" data-attributes="member: 288071"><p>I like it for thumb firing. Haven't had a chance to use the RX200s yet as the first one was DOA and I haven't tested the 2nd I bought. I like it fine so far but haven't used it much (5 mods on my desk right now) but it does not sit perfectly flat for me and has a little bit of wobble front to back.</p><p></p><p></p><p></p><p>Home Depot neoprene washers in the specialty drawers, in the screw aisl of the hardware section. Someone in another thread suggested mylar 7/8"/22mm washers but I couldn't find any at HD. I thought I bought some 'fiber' washers too that seemed a bit thick that I wanted to have/try just in case, but not seeing them in my mess of gear/parts now.</p><p></p><p>The RX200s that was DOA: I tried a few RTA's on it and they all gapped (I should have watched mike vape's youtube reviews before ordering them) but my cubis and cubis pro sub ohm tanks are fine. kidneypuncher has washers called mod guards designed for this issue.</p></blockquote><p></p>
[QUOTE="Fozzy71, post: 18239557, member: 288071"] I like it for thumb firing. Haven't had a chance to use the RX200s yet as the first one was DOA and I haven't tested the 2nd I bought. I like it fine so far but haven't used it much (5 mods on my desk right now) but it does not sit perfectly flat for me and has a little bit of wobble front to back. Home Depot neoprene washers in the specialty drawers, in the screw aisl of the hardware section. Someone in another thread suggested mylar 7/8"/22mm washers but I couldn't find any at HD. I thought I bought some 'fiber' washers too that seemed a bit thick that I wanted to have/try just in case, but not seeing them in my mess of gear/parts now. The RX200s that was DOA: I tried a few RTA's on it and they all gapped (I should have watched mike vape's youtube reviews before ordering them) but my cubis and cubis pro sub ohm tanks are fine. kidneypuncher has washers called mod guards designed for this issue. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
E-Cigarette Community
New Members: Introduce Yourself!
Picture of Your Setup Part 3!
Top
Bottom
Forums
Products
Vaping.com
Star Suppliers
Blogs
Menu
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
Accept
Learn more…