Reply to thread

Message

<blockquote data-quote="Spydro" data-source="post: 22059717" data-attributes="member: 132438">Hope you bought a low profile 2.1 and not the earlier standard 2.1 with a higher atty base that was designed for carto&#039;s, atty&#039;s or modified atty&#039;s to go down into their deeper catch cup to reach the 510.&nbsp;I could make a long list of the original atty&#039;s I bought for my Reos... years ago.&nbsp; But a problem with input from me now days is your quest for a &quot;modern&quot; atty that will fit on it.&nbsp; IOW, I haven&#039;t followed any small diameter atty&#039;s below 22mm-25mm-30mm for years, and none but mesh atty&#039;s for the past couple of years.&nbsp; Your limiting factors will be a diameter small enough to sit on top with no overhang (the Nuppin&#039; is 18mm), their AFC(&#039;s) being DL capable or modifiable for it, and being BF ready for squonking.I first started with MTL BF atty&#039;s that I drilled the AFC larger until better/higher quality attys&#039; were found or came out (RM2&#039;s, RM3&#039;s, Viscious Ant Cyclones. ERA&#039;s, etc).&nbsp;&nbsp; I&#039;d suggest a search to see what is available these days in 16mm-18mm BF atty&#039;s and then go from there.Originals I doubt are still available, but you might still be able to get a clone Origen Sweet 16 (16mm) from China.&nbsp; Thre originals were $100+ (I have 4 of them), but the clones were no more than $10-$15 IIRC.&nbsp; They can be either single or double coil.&nbsp; With both AFC&#039;s wide open they are still a restricted DL draw though unless you drill the AFC&#039;s larger.&nbsp; They can be a great little flavor atty.HTHO-16[ATTACH=full]837147[/ATTACH] [ATTACH=full]837151[/ATTACH] [ATTACH=full]837153[/ATTACH]</blockquote>

[QUOTE="Spydro, post: 22059717, member: 132438"] Hope you bought a low profile 2.1 and not the earlier standard 2.1 with a higher atty base that was designed for carto's, atty's or modified atty's to go down into their deeper catch cup to reach the 510. I could make a long list of the original atty's I bought for my Reos... [U]years ago[/U]. But a problem with input from me now days is your quest for a "modern" atty that will fit on it. IOW, I haven't followed any small diameter atty's below 22mm-25mm-30mm for years, and none but mesh atty's for the past couple of years. Your limiting factors will be a diameter small enough to sit on top with no overhang (the Nuppin' is 18mm), their AFC('s) being DL capable or modifiable for it, and being BF ready for squonking. I first started with MTL BF atty's that I drilled the AFC larger until better/higher quality attys' were found or came out (RM2's, RM3's, Viscious Ant Cyclones. ERA's, etc). I'd suggest a search to see what is available these days in 16mm-18mm BF atty's and then go from there. Originals I doubt are still available, but you might still be able to get a clone Origen Sweet 16 (16mm) from China. Thre originals were $100+ (I have 4 of them), but the clones were no more than $10-$15 IIRC. They can be either single or double coil. With both AFC's wide open they are still a restricted DL draw though unless you drill the AFC's larger. They can be a great little flavor atty. HTH O-16 [ATTACH=full]837147[/ATTACH] [ATTACH=full]837151[/ATTACH] [ATTACH=full]837153[/ATTACH] [/QUOTE]

Verification

Search

Search

Reply to thread