Hey. Just bought pro tank 3 on my svd. How much watts and volts do you use on 2.0ohm head? I'm using 8.5w and 4.3v.. Just wanna know what w and v configuration you use! Thanks!
Protank 3 watts and volts
- Thread starter Redistedis
- Start date
- th_trl_thread_readers 0
- Status
You are either it wattage mode or voltage mode you don't have to set both. Voltage will give you a set voltage no matter what the ohm rating of the coil. Wattage mode will adjust the voltage to achieve the set wattage automatically on different ohm coils. With a 2ohm coil I'd just start at around 3.8ish volts and go up from there til you're happy with it. If you start getting a burnt taste or something then back it off a little bit.
Sent from my DROID4 using Tapatalk
Sent from my DROID4 using Tapatalk
I have a Provari that I'm using right now and the best setting for me is between 3.8 and 4.0 volts depending on the juice I'm using. I also have a K200. I never use the watts setting, but the voltage is the same at 3.8 to 4.0 depending on the juice.
Also, it's somewhat of a personal opinion. If you like a better throat hit just keep going up until you find what works best for you. At some point you will get to a voltage or wattage that is too high. You will know because your juice will taste burnt.
Also, it's somewhat of a personal opinion. If you like a better throat hit just keep going up until you find what works best for you. At some point you will get to a voltage or wattage that is too high. You will know because your juice will taste burnt.
As said, it is a personal preference. I find that fruit juice work best for me between 3.9 - 4.2 volts. Another juice that I make myself, which consists of honey and carmel, works best at around 3.7 volts. Play with it and see what you like; you will notice a difference...
And, welcome to ECF!
And, welcome to ECF!
Also keep in mind that the protank 3 is dual coil, so what you use for volts/watts with that will be different than what you would use on a single coil like the protank 2. Start low and work your way up until you find that sweet spot.
Yeah, basically what everyone else said.
Voltage is like a manual mode on your ecig. Wattage mode is like auto-pilot and will automatically set the output voltage based on your the applied load (the resistance of your coil: AKA ohms). You should use your wattage setting if you are switching between multiple tanks because it will automatically set the voltage to about where you should like it (which is typically in the same range if you are just using clearomizers and not switching between clearos and RDA's/RBA's, etc..) Most people are happy with a wattage of about 7-9 (I prefer 8) on a standard clearomizer (like your protank 3).
Just play around with the settings and you will figure out what you like. The main thing to note is that the wattage settings and voltage settings are independent of each other and cannot be used simultaneously. Other than that just mess around and
Voltage is like a manual mode on your ecig. Wattage mode is like auto-pilot and will automatically set the output voltage based on your the applied load (the resistance of your coil: AKA ohms). You should use your wattage setting if you are switching between multiple tanks because it will automatically set the voltage to about where you should like it (which is typically in the same range if you are just using clearomizers and not switching between clearos and RDA's/RBA's, etc..) Most people are happy with a wattage of about 7-9 (I prefer 8) on a standard clearomizer (like your protank 3).
Just play around with the settings and you will figure out what you like. The main thing to note is that the wattage settings and voltage settings are independent of each other and cannot be used simultaneously. Other than that just mess around and
I use my Vamo set to 8 watts on 1.8 coils whether I am using my Protank , Evod, or Kayfun. Once in a while they will have a harsh hit and I'll lower it to 7 for a few hits.
- Status
Similar threads
- Locked
- Locked
