The costs of running this huge site are paid for by ads. Please consider registering and becoming a Supporting Member for an ad-free experience. Thanks, ECF team.

Pulse BF build?

Discussion in 'Bottom Feeder Mods' started by Triston Robinson, Nov 6, 2017.

Tags:
Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. Triston Robinson

    Triston Robinson Full Member

    Aug 24, 2017
    Hey guys, I just got ahold of my first squonker and I’m looking for a good build for it. I hear about people getting a really hot intense vape from tube mods and I want to put a similar build in this. What kind of builds are you guys running?
     
  2. Izan

    Izan Vaping Master ECF Veteran

    Jul 1, 2012
    Mallorca, Spain
    Hi,
    What atty do you have?
    What wire do you have?
    What battery do you have?
    Will you build a single or dual coil?
    What are you using to test your build before using it on the squonker?

    Cheers
    I
     
  3. Triston Robinson

    Triston Robinson Full Member

    Aug 24, 2017
     
  4. Triston Robinson

    Triston Robinson Full Member

    Aug 24, 2017
    I’m using the icon rda with a dual coil ni80 build- an 8 wrap around a 3mm ohming to around .18. My batteries are 3000mah 3.7 volt but I am unsure of the amperage of them.
     
  5. Izan

    Izan Vaping Master ECF Veteran

    Jul 1, 2012
    Mallorca, Spain
    mooch2017.jpg
    SAFER.jpg

    Did you do the build on the icon?
    Is the battery an 18650?
    Do you only have the nichrome wire? What is the AWG?


    know your gear- (BadNinja)
    Be safe
    I
     
    • Like Like x 1
  6. Triston Robinson

    Triston Robinson Full Member

    Aug 24, 2017
    The batteries are LG HG2 and I did the build myself with 22g nichrome. It is the only wire I use because it heats up a little faster. Is there a better wire I could be using?
     
  7. puffon

    puffon Vaping Master Verified Member ECF Veteran

    Sep 18, 2014
    Florida
    Using your .18 ohm build, you are drawing over 23amps.
    The LG HG2 is rated for only 18amps.
    Get some Sony VTC5a's if you want to build that low, otherwise rebuild to .3ohm or above.
    Battery drain | Steam Engine | free vaping calculators
     
    • Agree Agree x 1
  8. Triston Robinson

    Triston Robinson Full Member

    Aug 24, 2017
    Thanks man. But how do I make a hot dense build if I were using VTC5a’s?
     
  9. puffon

    puffon Vaping Master Verified Member ECF Veteran

    Sep 18, 2014
    Florida
    The build you are using, should get what you're looking for safely, using a VTC5a
     
  10. Ivan Ceron

    Ivan Ceron New Member

    Feb 3, 2018
    Im also using the Pulse bf with a Pulse 24. I'm currently using a dual coil 22 awg N80, 9 wraps around 3mm and reads at .19/.2 ohms. I also use vtc5a and 5 leg Ijoy 20700 batteries. But I'm noticing that it takes about 3 to 4 seconds to fully ramp up. Is this normal? Once it gets going it's decent.
     
Thread Status:
Not open for further replies.

Share This Page

  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice