question about Kanger aerotank with mech mod

[oto260]

Hello, so recently I have bought a Nemesis mod and a kanger aerotank, it's getting shipped to me. But now I believe that I made mistake by buying aerotank, because from the batteries I get about 3.7 volts and I heard that it might be not enough for the aerotank.
Should I be searching for a another clearomizer or I'm just being silly right here.

 

[Completely Average]

Hello, so recently I have bought a Nemesis mod and a kanger aerotank, it's getting shipped to me. But now I believe that I made mistake by buying aerotank, because from the batteries I get about 3.7 volts and I heard that it might be not enough for the aerotank.
Should I be searching for a another clearomizer or I'm just being silly right here.

Get a Kick, set it to about 8.25 watts, and you're all good. Kick units cost around $15.

I happen to be using that exact setup right now...

 

[Frenchfry1942]

It works for me. I use 1.8 ohm resisters.

On another note, I don't have just one of anything. To much opportunity for something to go bad and I not be prepared.

 

[LX1X]

Hello, so recently I have bought a Nemesis mod and a kanger aerotank, it's getting shipped to me. But now I believe that I made mistake by buying aerotank, because from the batteries I get about 3.7 volts and I heard that it might be not enough for the aerotank.
Should I be searching for a another clearomizer or I'm just being silly right here.

Not true.. a fresh battery will start at 4.2v.. as it drains... your voltage drops.

You should be good with 2 ohm coil.

 

[oto260]

Alright, I'm not chaging anything. Just going to wait for my shippment

 

[Completely Average]

Alright, I'm not chaging anything. Just going to wait for my shippment

Yeah, don't change it. With a good Kick module this thing hits like a freight train.

 

[Nightshard]

Rebuild your coil to 1.3-1.5

 

[Bobw1951]

I don't have my Nemesis yet, but the Aerotank works just great on my GP Paps clone with a 800 mAh 18350 battery so should work fine on the Nemmy

 

[CaCHooKa Man]

I have a Sentinel V1 and I've been having problems with my Aerotank. There's barely any vapor when I use it. I've tried both of the included coils and it's the same with both of them. I'm using an IMR 18650 2000mAh 3.7 volt battery but I have some Sony VTC5s in the mail that should arrive by Saturday. Do I need to rebuild the coils for it to work properly?

 

[Bobw1951]

I have a Sentinel V1 and I've been having problems with my Aerotank. There's barely any vapor when I use it. I've tried both of the included coils and it's the same with both of them. I'm using an IMR 18650 2000mAh 3.7 volt battery but I have some Sony VTC5s in the mail that should arrive by Saturday. Do I need to rebuild the coils for it to work properly?

First of all take it apart and make sure the atomizer is fully screwed into the base, also make sure the adjuster is fully open so that you can see all the airholes. See if that makes any difference.

 

[teddybear2566]

i have this setup and is work just fine, BUT beware I have noticed and email kanger about this issue ( on some mods like the smok magento i bought it does not matter how I change the contact pins it still shorts) i am thinking about milling down the contact on the aero its self due to this issue, so just keep i eye on your batt temp at first to be safe ( had two batties try to blow up)

 

[Bigflyrodder]

Should work fine, really should think about picking up a Kick at some point though. The performace will drop as the battery drains without one and for me personally I don't enjoy using any of my tanks below about 4.0v which means I'd only get about an hour or so use before I had to swap batteries. YMMV

 

[angnjc]

Get a Kick, set it to about 8.25 watts, and you're all good. Kick units cost around $15.

I happen to be using that exact setup right now...

Where did you find a kick for $15, everywhere I have looked they are $20+. Maybe I'm looking in the wrong places.