Reuleaux RX200S TC Problem

[humax]

Hi All

I'm having a problem with my reuleaux RX200S I am trying to use it in TC for SS but as soon as I hit the fire button it keeps changing back to VW mode. Has anyone had this problem before with a reuleaux RX200S ?

 

[daviedog]

Will it support SS wire.
There is more than one SS wire available for vaping..

 

[mongo74]

What's your build? What wattage are you firing it at in TC? Also, try spacing the coils.

 

[humax]

Will it support SS wire.
There is more than one SS wire available for vaping..

Hi

Yes it has a setting for SS.

 

[humax]

What's your build? What wattage are you firing it at in TC? Also, try spacing the coils.

Hi

I'm firing at 30w and have set the temp at 420 with coils at 0.26

 

[daviedog]

Hi

Yes it has a setting for SS.

I have an eviv vtc mini, bought SS304, threw me right out to power mode. The SS316 worked well.
Your TC numbers are fine.
Coil resistance is not a factor in a regulated mod..

 

[humax]

I have an eviv vtc mini, bought SS304, threw me right out to power mode. The SS316 worked well.
Your TC numbers are fine.
Coil resistance is not a factor in a regulated mod..

I'm starting to think the mod might be broken as i have had problems with it before. But I'm going to try and build the coils again and see if its any better.

 

[KenD]

I'm starting to think the mod might be broken as i have had problems with it before. But I'm going to try and build the coils again and see if its any better.

You're using ss316, right? Make sure that all your connections are tight, and the 510 in the mod and atty clean.

Sent from my M7_PLUS using Tapatalk

 

[humax]

Hi

No, I'm using 317L stainless steel

 

[KenD]

Hi

No, I'm using 317L stainless steel

Ok. You should use the proper tcr for ss317l. Check steam-engine.org for that.

Sent from my M7_PLUS using Tapatalk

 

[Falco78]

I've only had issue with my RX200 with some ribbon SS316L but I am now doubting if the wire was legit as I've never had an issue with any other wire while in TC

sent from my Galaxy Note 4 using MOAR 2.1b ROM running tapatalk

 

[Eskie]

The difference in TCR between 316 and 317 is pretty small.

If you're popping into wattage mode recheck the build. If you still pop back into wattage mode, try a different atty that does work on a different TC mod (should you have one). If that one pops back into wattage mode the problem is likely with the mod, probably the 510 connector.

 

[Falco78]

On mine is don't have near as good of a vape using the above TCR as using the prebuilt in SS mode

sent from my Galaxy Note 4 using MOAR 2.1b ROM running tapatalk

 

[Eskie]

On mine is don't have near as good of a vape using the above TCR as using the prebuilt in SS mode

sent from my Galaxy Note 4 using MOAR 2.1b ROM running tapatalk

It's whatever works best for you that counts.

 

[humax]

I rebuilt the coil again the same way i did the last one but this time its working fine. Not sure what i did wrong the first time.

 

[humax]

Spoke too soon,it worked great for about an hour and now its clicking back to VW mode again

 

[Falco78]

Have you tried to put the firmware on again?

sent from my Galaxy Note 4 using MOAR 2.1b ROM running tapatalk

 

[humax]

Have you tried to put the firmware on again?

sent from my Galaxy Note 4 using MOAR 2.1b ROM running tapatalk

Yes i tried that. Funny thing is i did the same build on a Limitless+ and it worked fine. Not sure if this is a Bellus problem with it having a small deck.

 

[speedy_r6]

What resistance are you running with the new setup? Is it still the 0.26 ohms? If so, try building with a higher resistance. On my plain rx200, I notice that it kicks out of TC and into wattage mode A LOT if I run under .3 ohms. It has yet to kick me out of TC with a build of 0.4 or higher.

 

[humax]

What resistance are you running with the new setup? Is it still the 0.26 ohms? If so, try building with a higher resistance. On my plain rx200, I notice that it kicks out of TC and into wattage mode A LOT if I run under .3 ohms. It has yet to kick me out of TC with a build of 0.4 or higher.

To get 0.3 to 0.4 ohms that would need 10 to 14 wraps I'm not sure i would be able to fit a spaced coils that size in the Bellus