So I had the Wismec RX300 for less than 2 weeks, and began discovering issues right away (now I have a Smok GX350 where none of these issues are present).
The first issue is the 510 connection. Tell me why it stopped working with the Neutron RDA on day 2, wouldn't make a connection at all. By week 2 (yesterday) the Reux tank wouldn't make a connection either. I thought the Nuetron RDA was a problem and didn't want to go through the trouble or returning anything/ spending the money for a new mod, but it turned out to be the 510 connection.
If that wasn't enough, TC mode is totally defective. I get "atomizer low" errors on any build less than .15 ohms, and it is constantly slipping out into power mode, or will not even allow me to use TC mode unless I spend 20 minutes retrying, or leaving the mod alone for a while, on builds that did work in TC mode. I have never gotten any build to last me more than a few hits in TC mode even when they did work, however. I experienced this when my Reux tank was still working, and with the Inde Duo RDA that I have.
None of these problems occur on my IPV D3. Every atomizer makes a connection, and TC mode works perfectly, everytime.
Though I would have enjoyed not being limited to a brand, thank god I only used Wismec atomizers and kept my warranty in tact. Eciggity.com agreed to refund me for the mod after I uploaded videos for them documenting my obvious issues.
My Smok GX350 works with everything just like my IPV D3. And since it is much smaller than the RX300, I like it. I am not too ...... about having to go through this since Eciggity provided great customer service in the end. Just mad that I had to buy a Reux tank instead of a TFV12. The original RTA section on that tank that came with the original package was very difficult to use. The clamp style that this particular RTA had was impossible for me to work with for dual coils due to limited space, and height that the clamps would rise up to on the screws. I stripped the screws pretty quickly trying to mess with it, although there is another set, but I would never use that deck again. Also, the coil heads are not very powerful, and dont take full advantage of the mod they were designed for. I ended up buying the velocity style replacement deck, and have had no issues with it. It is a smaller build deck for the air flow this tank can provide, but a great deck all in all.
I am not recommending people do not buy the rx300, although I am sure it seems like it. I am happy I replaced it with the gx350 in the end. But I did like the few extra display features that the rx300 came with. These are simply not worth the issues that I had with product. Hopefully anyone who has bough one or is going to will not have to deal with any of this. I envy you if that is the case, I really thought I was going to love the RX300.
The first issue is the 510 connection. Tell me why it stopped working with the Neutron RDA on day 2, wouldn't make a connection at all. By week 2 (yesterday) the Reux tank wouldn't make a connection either. I thought the Nuetron RDA was a problem and didn't want to go through the trouble or returning anything/ spending the money for a new mod, but it turned out to be the 510 connection.
If that wasn't enough, TC mode is totally defective. I get "atomizer low" errors on any build less than .15 ohms, and it is constantly slipping out into power mode, or will not even allow me to use TC mode unless I spend 20 minutes retrying, or leaving the mod alone for a while, on builds that did work in TC mode. I have never gotten any build to last me more than a few hits in TC mode even when they did work, however. I experienced this when my Reux tank was still working, and with the Inde Duo RDA that I have.
None of these problems occur on my IPV D3. Every atomizer makes a connection, and TC mode works perfectly, everytime.
Though I would have enjoyed not being limited to a brand, thank god I only used Wismec atomizers and kept my warranty in tact. Eciggity.com agreed to refund me for the mod after I uploaded videos for them documenting my obvious issues.
My Smok GX350 works with everything just like my IPV D3. And since it is much smaller than the RX300, I like it. I am not too ...... about having to go through this since Eciggity provided great customer service in the end. Just mad that I had to buy a Reux tank instead of a TFV12. The original RTA section on that tank that came with the original package was very difficult to use. The clamp style that this particular RTA had was impossible for me to work with for dual coils due to limited space, and height that the clamps would rise up to on the screws. I stripped the screws pretty quickly trying to mess with it, although there is another set, but I would never use that deck again. Also, the coil heads are not very powerful, and dont take full advantage of the mod they were designed for. I ended up buying the velocity style replacement deck, and have had no issues with it. It is a smaller build deck for the air flow this tank can provide, but a great deck all in all.
I am not recommending people do not buy the rx300, although I am sure it seems like it. I am happy I replaced it with the gx350 in the end. But I did like the few extra display features that the rx300 came with. These are simply not worth the issues that I had with product. Hopefully anyone who has bough one or is going to will not have to deal with any of this. I envy you if that is the case, I really thought I was going to love the RX300.
