Last edited:
-
Need help from former MFS (MyFreedomSmokes) customers
Has any found a supplier or company that has tobacco e-juice like or very similar to MFS Turbosmog, Tall Paul, or Red Luck?
View thread
- Status
place one probe on the outside of the 510 connector and the other on the centre pin with the meter set to ohms and see what you get and come back and tell us
Last edited:
And if you suspect the s-wire check the resistance from the center post on the bottom and the long screw.
My 701 mouthpiece was tight to start with also.
I have many for using on the Bulli A2 so was not concerned with breaking the G tank mouthpiece, so I just forced it off.
After first clean and a new mouthpiece screwed on & off a few times, it was easier.
Could just be s**t in the threads.
I have many for using on the Bulli A2 so was not concerned with breaking the G tank mouthpiece, so I just forced it off.
After first clean and a new mouthpiece screwed on & off a few times, it was easier.
Could just be s**t in the threads.
Thanks to everybody chiming in with valuable info. I'll give 32g kanthal another shot although I could see using thinner wire later. I got used to high volts vaping (4.6--5.0V) so my attys are in 3-4 ohms range, which would be hard to get with 32g kanthal.
Are you guys using #440 mesh or #330? I ordered #440 which I've got, but they also send extra two bonus sheets of coarser mesh (assume it is #330 or similar). I feel like #330 stuff is easier to work with, although I didn't progress far enough to assess quality of wicking, flavor vs #440 wick.
Are you guys using #440 mesh or #330? I ordered #440 which I've got, but they also send extra two bonus sheets of coarser mesh (assume it is #330 or similar). I feel like #330 stuff is easier to work with, although I didn't progress far enough to assess quality of wicking, flavor vs #440 wick.
Ah, a high volter..... You can just double up the wire, I've done it before. It works, but not for me because 4.60 is my absolute high end and I do that on 3.0 cartos usually...
Ohms read 1.7 unwrapped. I just screwed it onto a disposable 510 batt and got a 3.1v reading.I did this after readjusting the S wire. At least now I know it works. Thanks for the suggestions guys.
Is anyone actually getting good flavor out of this?
All my other genisis mods are rocking. But very faint flavor with gtank. I got a coil to 2.0ohm, now it works on my provari.
Sent from my HTC Glacier using Tapatalk
All my other genisis mods are rocking. But very faint flavor with gtank. I got a coil to 2.0ohm, now it works on my provari.
Sent from my HTC Glacier using Tapatalk
Mine has great flavor. There are quite a few that aren't getting flavor and I'm not sure why. Chuckie, what ohms do you get from the center pin on the bottom to the positive screw in the chamber?
who ever does not like his g-tank send me a pm and I will give it a good home!!
Hehe, I'm actually rather partial to a few banana flavors. I'm pretty sure you'll find another soon enough, you checked the classifieds? Someone from the 'no flavor' club is bound to pack it in.
Sure thing. I'm still using this coil and wick, somewhere around a week:
I don't think it's too much airflow, this is pretty stiff. Not too much so, but I feel like it would be good for a pipe style mod and good for puffing on. It is real easy to get too much throat hit on this, but I think it was the wick being a bit too loose in the tank hole and the coil too wet.
I don't think it's too much airflow, this is pretty stiff. Not too much so, but I feel like it would be good for a pipe style mod and good for puffing on. It is real easy to get too much throat hit on this, but I think it was the wick being a bit too loose in the tank hole and the coil too wet.
- Status
Similar threads
