SXK DOGGY STYLE

[kinda]

As for the popping,never had it on a Doggy but normally a sign of too loose wick in the coil.

With my rda I try to wick pretty tight but I wasn't sure about MTL RTAs. My first go I thought I had too much cotton because the videos I watched looked like it was moving through the coil somewhat easily. So I tried to make it snug but not to where the coil wanted to move when I pulled it through. I'll try it a bit tighter next time. Thank you!

 

[osso1]

Doggy Tip...
I use a Nickel to tighten bell Cap
Put in the slots on Bellcap turn it tight

My 5 cent Tool....

 

[oplholik]

Ha ha, my tool is more expensive than yours. I use a 25cent tool.

 

[Dubminer]

Doggy Tip...
I use a Nickel to tighten bell Cap
Put in the slots on Bellcap turn it tight

My 5 cent Tool....

I use a teaspoon.

 

[Ryedan]

You shamed me into it.

I apologise Chodi! That was not my intention at all

I used one of my SJMY Doggy cause it was handy and wound a 2mm VV Clapton Superfine ss coil. I left it slightly spaced. The best I could get in that tiny deck was a .51ohm coil. That was a very tight fit. I put it on my P80 mod and set to tc. I normally vape tc on doggies around 400F but this required me to drop it to 350F unless I wanted to melt the tank (and possibly my mouth). I cranked down the watts setting to only 12w (in tc). It produces a fantastic flavorful doggy vape. It is producing more vaper than I get with a simple round wire ss coil. I can say that it raises the flavor a bit but not dramatically. Most noticeable is the increased vapor. It is a warmer vape and I would not advise chain vaping on it as the tank starts to heat up.

I will probably go back to my ss round wire builds for the doggy in the future. The VV Superfine wire has done some amazing things for a few of my rta's but with the doggy it may be a little overkill at least for me.

Thanks for the feedback, it is much appreciated. I've always used basic single SS wire coils with my Doggies but you've got me intrigued and motivated to try some other setups now

 

[Asbestos4004]

I use a teaspoon.

I use a Titanium chamber torque wrench designed specifically for the doggystyle by a machinist in Romania. I waited on his Facebook list for 2 years and finally won a raffle which put me in a lottery which gave me a 1 in 100 chance to get one. Well, that didn't work out. So, after finding 25 people to vouch for me, I was finally admitted into a secret Facebook group for Ti DS (TIDS) wrench owners. Im ashamed to admit that I paid flipper prices. $2900 for a $750 wrench is ridiculous, I know. But my Chambers are all perfectly torqued and as a result, I'm fairly confident that the flavor I'm getting is way better than all of yours.
Plus, it's just dangerous vaping an atty that had loose change or silverware near the chamber. A little vape responsibility goes a long way, people.

 

[Kusie]

LOL, Spot on!

 

[Katdarling]

I use a Titanium chamber torque wrench designed specifically for the doggystyle by a machinist in Romania. I waited on his Facebook list for 2 years and finally won a raffle which put me in a lottery which gave me a 1 in 100 chance to get one. Well, that didn't work out. So, after finding 25 people to vouch for me, I was finally admitted into a secret Facebook group for Ti DS (TIDS) wrench owners. Im ashamed to admit that I paid flipper prices. $2900 for a $750 wrench is ridiculous, I know. But my Chambers are all perfectly torqued and as a result, I'm fairly confident that the flavor I'm getting is way better than all of yours.
Plus, it's just dangerous vaping an atty that had loose change or silverware near the chamber. A little vape responsibility goes a long way, people.

 

[MrIzzy]

Love my doggy

 

[oplholik]

Kinda like that tank.

 

[Katdarling]

What tank is that? I'm lost, so to speak.

 

[MrIzzy]

Its doggystyle RTA. I just made a custom full ultem accessories for it.

 

[vapdivrr]

Its doggystyle RTA. I just made a custom full ultem accessories for it.

I normally don't go for ultem, but that's pretty sweet....bad doggy

Sent from my SCH-I545 using Tapatalk

 

[Kusie]

Its doggystyle RTA. I just made a custom full ultem accessories for it.

Wow, I mean ... how did you do that? That looks highly professional, even the airflow ring is custom made from ultem? Badass!!

 

[Asbestos4004]

Love my doggy

Mom always said "bring enough for everyone or it's rude"..... So, should we all pm our addresses to you?

 

[Dropmyload]

I want one!!!!!!!!!!!!!!!!!!!!!!!!!!

 

[Chodi]

I'm guessing the man owns a quality 3D printer.

 

[MrIzzy]

Actually I've made a list for all my supporters in Malaysia and the list is currently full (50/50)

The batch serial number will starts from #000 (which is mine) until #050. Maybe I can open the list again for you guys once I've finished with this current batch. You know, Ultem material is pretty expensive nowadays and a bit hard to get from my suppliers.

Please do hit me on whatsapp for further talk +60196345465

 

[MrIzzy]

And thanks guys for your positive feedbacks. Appreciate it.

 

[Dropmyload]

Actually I've made a list for all my supporters in Malaysia and the list is currently full (50/50)

The batch serial number will starts from #000 (which is mine) until #050. Maybe I can open the list again for you guys once I've finished with this current batch. You know, Ultem material is pretty expensive nowadays and a bit hard to get from my suppliers.

Please do hit me on whatsapp for further talk +60196345466

Very nice, but that number doesn't seem to be on whatsapp.....