SXK Nebula Wine RTA

[Buster282]

My glass broke today but I just got it workin with a Sub tank glass and o-rings. Yay! Doubled up the sub rings on the bottom. I had to put the big beveled one on the glass after filling then screw on the base. The smaller flat one I put on the base. She ain't pretty but she does have bubbles..

 

[zoiDman]

My FT SXK Wine arrived today.

Nice tank. It has a Very Clean and Simple Look. The Build Quality is Pretty Good. The Hit/Flavor seem Good also.

The Air Flow (for Me) was a little to Wide Open. But I like a More Restrictive Flow than most. And it was Nothing that a Bamboo Skewer couldn't Fix by plugging one of the Inlet Holes.

I haven't tried to Take the Glass Off yet. But when I did the Pre-1st Fill rinse in warm water, I gave it a Slight Tug. I could feel it move Slightly so I don't think there is going to be a problem getting it off.

Overall, I'm Happy with it. Especially at the Price it was going for.

 

[zoiDman]

UPDATE:

After about an Hour or some of vaping, I'm past the Initial Coil "Break-In" period.

And the Flavor has gone from Good into Very Good.

 

[Roadtrip635]

I ordered a black one from FT, it should be here next week! I'm looking forward to it.

 

[Roadtrip635]

UPDATE:

After about an Hour or some of Vaping, I'm past the Initial Coil "Break-In" period.

And the Flavor has gone from Good into Very Good.

What kind of build did you put in it?

 

[zoiDman]

I ordered a black one from FT, it should be here next week! I'm looking forward to it.

I think you will Like it.

What kind of build did you put in it?

It has a 1.0 Ohm 3.0mm Coil made from 28ga NiChrome 80. Wicked with Muji Pad Cotton.

I didn't know what it would like Wick-Wise. So I just trimmed the wick ends into Blunt Points that reached the Bottom of the e-Liquid Inlet Slots. Wicks Great. And No Leaking.

BTW - I can Verify that these O-Rings work well if anyone is looking for Replacement O-Rings for this Wine RTA.

$0.80 Rubber O-Ring Seals for E-Cigarette (20-Pack) 20-pack - 16*14*1mm (OD*ID*W) at FastTech - Worldwide Free Shipping

 

[Roadtrip635]

I think you will Like it.



It has a 1.0 Ohm 3.0mm Coil made from 28ga NiChrome 80. Wicked with Muji Pad Cotton.

I didn't know what it would like Wick-Wise. So I just trimmed the wick ends into Blunt Points that reached the Bottom of the e-Liquid Inlet Slots. Wicks Great. And No Leaking.

BTW - I can Verify that these O-Rings work well if anyone is looking for Replacement O-Rings for this Wine RTA.

$0.80 Rubber O-Ring Seals for E-Cigarette (20-Pack) 20-pack - 16*14*1mm (OD*ID*W) at FastTech - Worldwide Free Shipping

Thanks!
lol! I have a pack of those o-rings and a spare glass coming as well, just in case.
If you get a chance, I'd love to see a pic!

 

[zoiDman]

Thanks!
lol! I have a pack of those o-rings and a spare glass coming as well, just in case.
If you get a chance, I'd love to see a pic!

These are some Pretty Crumby pictures. But here you go...

I'm not sure Why? But whenever I take a picture of a Mod, that my Hand looks Better and is Clearer than the Mod that I am Holding.

 

[Roadtrip635]

These are some Pretty Crumby pictures. But here you go...

View attachment 518919

View attachment 518920

I'm not sure Why? But whenever I take a picture of a Mod, that my Hand looks Better and is Clearer than the Mod that I am Holding.

Nice simple, elegant tank, it looks good. Did you change out the blue o-rings for the black you ordered or did it come installed with the black ones?

 

[zoiDman]

Nice simple, elegant tank, it looks good. Did you change out the blue o-rings for the black you ordered or did it come installed with the black ones?

I did. Mine came just like the FT in the Fasttech picture. Blue O-Rings installed. Orange ones as spares.

Really Linking this Tank. I'm a Flavor Chaser. And the Flavor from it is Very Good. It has Clean, Simple look to it also. It reminds me of a Goblin Mini. Sans the Leaking.

ETA: The Adjustable 510 Pin is also a Nice Touch. I like to set up my Mech Mods with "Hard" 510 Pins. When I screwed on this Wine Tank with a .020" Black Spacer under the Tank, it didn't make contact with either my Windrose or my Carvella. But a Half Turn out on the 510 Pin of the Tank and I was in Business.

 

[VapingTurtle]

...
The Air Flow (for Me) was a little to Wide Open. But I like a More Restrictive Flow than most. And it was Nothing that a Bamboo Skewer couldn't Fix by plugging one of the Inlet Holes.
...

I have been enjoying this tank very much. Spare glass and o-rings are on their way to me from FT.

I also like a tighter draw than this has. Here was my perfect answer at a really cheap price:
PTFE Teflon Tubing 4mm OD 2mm ID for RepRap Prusa Rostock Makerbot by the Inch!

A little snip of the PTFE tube right in the air outlet below the coil, and perfect draw now. Just a bit more air than my KFLs.

 

[zoiDman]

I have been enjoying this tank very much. Spare glass and o-rings are on their way to me from FT.

I also like a tighter draw than this has. Here was my perfect answer at a really cheap price:
PTFE Teflon Tubing 4mm OD 2mm ID for RepRap Prusa Rostock Makerbot by the Inch!

A little snip of the PTFE tube right in the air outlet below the coil, and perfect draw now. Just a bit more air than my KFLs.

That's a Good Call VT.

I think I will go that route when I cut the Chimney Down so I can use a piece of 30mm Subtank Mini Glass.

Hey if I don't see you. Have a Great New Year VapingTurtle. And All the Best in 2016.

 

[VapingTurtle]

Hey if I don't see you. Have a Great New Year VapingTurtle. And All the Best in 2016.

And a happy and healthy new year to you, zoiD, and to all of you (sxk) Winoes.

 

[zoiDman]

SXK Winoes.

Love It!

 

[ThunderDan]

I got mine in yesterday when I came home from Christmas out of town. It looks pretty nice, haven't built it yet, still giving it a wash right now.

 

[VaPreis]

I finally broke my glass trying to take it off the top cap, and for no reason other then I wanted to win.

FYI: Just when you think you finally got it loose and it's starting to come off...that's when it shatters.

Got 2 replacements on order from Fasttech, along with some spare o-rings. Unfortunately, it says they're not shipping out until the 11th.

 

[zoiDman]

I finally broke my glass trying to take it off the top cap, and for no reason other then I wanted to win.

FYI: Just when you think you finally got it loose and it's starting to come off...that's when it shatters.

Got 2 replacements on order from Fasttech, along with some spare o-rings. Unfortunately, it says they're not shipping out until the 11th.

Yikes... That's Bad News. Sorry to hear that.

 

[cobalt327]

Been using my Wine on an eVic VTC Mini, so far I've used it w/316 SS @ 0.52 ohm and Ni200 @ 0.120 ohm. Low voltage drop and steady resistance in TC.

Airflow was a little too open for me so I used a silicone vape ring w/a 3/16" hole punched in it to block one air hole. Helped quiet the air intake as well.

 

[zoiDman]

UPDATE v2:

I filed down the Chimney by about .120" so I could use a 30mm Subtank Mini glass tank.

Worked Great. No Leaking. And the Flavor might even be a Tad Better due to the Smaller Chamber.

 

[cobalt327]

Has anyone here come up w/a combination of parts that will let a bellcap work? What about top fill?